Paper Titles
Experimental Study on New Bonding Materials for Developing Nano-Grinding Plates
p.489
Development of Electroplated CBN Wheel with Cemented Carbide Base for Precision Grinding of Compressor Cylinder Vane Slot
p.495
Shear Strength of Brazed Joint between Diamond Grains and Steel Matrix Using a Ni-Cr Filler Alloy
p.501
Theoretical Analysis and Simulation of Airflow of Super High-Speed Grinding Wheel
p.507
Abrasion Performances of Stainless Steel/Carbon Fiber Reinforced Polyetheretherketone (PEEK) Friction Material
p.511
Roundness Modeling Using Fractal Interpolation
p.521
An Evaluation on Surface Topography Finished by Abrasive Jet with Grinding Wheel as Restraint
p.527
Key Technologies of Image Measurement for Curve Accurate Grinding
p.533
Surface Roughness Prediction Based on Cutting Parameters and Nose Radius in Precision Turning
p.539

Abrasion Performances of Stainless Steel/Carbon Fiber Reinforced Polyetheretherketone (PEEK) Friction Material

Article Preview

Abstract:

A semi-metallic stainless steel/carbon fiber reinforced PEEK-based friction material was developed in this paper. The composite was PEEK 19.63wt%, stainless steel fiber 7.57 wt%, carbon fiber 10.97 wt%, cashew 6.51 wt% and fillers 55.33%. The molding process was blending for about 30 seconds at higher speed, pre-heating at the temperature of 80 for 30min, molding at 320 and pressure 35Mpa for 3min/mm, then post-curing at the temperature of 80 for 30min , 150 for 30min270 for 30min320 for 180min. The results of abrasion test showed that the developed material N3 had higher and steady friction coefficient and low abrasion value. The SEM morphology study showed that the wear mechanism was particle abrasion at low temperature but adherence abrasion as well as particle abrasion occurred at higher temperature. The cohesive strength of the composite and the heat-resistant property of resin matrix were the key factors affected wear loss. The abrasion depended on the strength of transformed films and matrix.

You might also be interested in these eBooks
Advances in Abrasive Technology IX View Preview

Info:

Periodical:

Key Engineering Materials (Volume 329)

Pages:

511-518

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.329.511

Citation:

Cite this paper

Online since:

January 2007

Authors:

Hua Fu, Bo Liao, Bao Chen Sun, Ai Ping Liu, Fang Juan Qi, Zhan Lai Ding

Keywords:

Abrasion Performance, Friction Behavior, PEEK, Semi-Metallic Friction Material, Stainless Steel Fiber, Wear Behaviour

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2007 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] Sheng Gang, Ma Baoji: The State of the Arts and Development of Studies on Friction Materials. Journal of Xi An Institute of Technology, Vol20 (1) (2000), pp.127-132.

Google Scholar

[2] Bijwe. J.: Composites as friction Materials: Recent Developments in Non-Asbestos Fiber Reinforced Friction Materials-A Review, Polym. Compos. Vol. 18 (1997), pp.378-396.

DOI: 10.1002/pc.10289

Google Scholar

[3] A.P. Harsha, U.S. Tewari: Tribological Studies on Glass Fiber Reinforced Polyetherketone Composites, Journal of Reinforced Plastics and Composites, Vol. 23 (2004), No. 1, pp.65-81.

DOI: 10.1177/0731684404029349

Google Scholar

[4] Y. LU: A Golden Section Approach to Optimization of Automotive Friction Material, Journal of Materials Science, Vol. 38 (2003): pp.1081-1085.

Google Scholar

[5] YUN HAE KIM, JUNG JU LEE: A Study on the Friction Characteristics of Automotive Composite Brake Pads Using Taguchi Method, International Journal of Modern Physics B, Vol. 17 (2003): pp.1845-1850.

DOI: 10.1142/s0217979203019769

Google Scholar

[6] Che Jianfei, Song Ye, etc: The Application of Uniform Design in Developing Friction Materials, Journal of Nanjing University of Science and Technology, Vol. 23 (1999): pp.249-252.

Google Scholar

[7] H. Jang, J.S. Lee, J.W. Fash: Compositional effects of the brake friction material on creep groan phenomena, Wear 251 (2001), pp.1477-1483.

DOI: 10.1016/s0043-1648(01)00786-4

Google Scholar

[8] Alexeyev N.M.: On the Motion of Material in the border Layer in Solid Friction, Wear, 139(1990), pp.33-43.

DOI: 10.1016/0043-1648(90)90208-r

Google Scholar

[9] Wirth,A., Eggleston,D. and Whistaker,R.: A Foundamental Tribochemical Study of the Third Body Layer Formed during Automotive Friction Braking, Wear, 179(1994), pp.75-81.

DOI: 10.1016/0043-1648(94)90222-4

Google Scholar

[10] Kostetsky B.I.: The Structure-Energetic Concept in the Theory of Friction and Wear(Synergism and Self-organization), Wear, 159(1992): pp.1-15.

DOI: 10.1016/0043-1648(92)90280-l

Google Scholar

[11] Jacko M.G.: Physical and Chemical Changes of Organic Disc Pads in Service, Wear, 46(1978): pp.163-175.

DOI: 10.1016/0043-1648(78)90118-7

Google Scholar