Paper Titles
Mechanical Joining of Magnesium Components by Means of Inductive Heating - Realization and Capability
p.1638
Selected Aspects of Semisolid Forming Magnesium Alloys
p.1644
Properties of AZ31 and AZ91 Sheets Made by Twin Roll Casting
p.1650
Superior Corrosion Resistance and Mechanical Properties of a Mg Alloy Recycled by Solid-State Process
p.1656
Effect of RE Elements and Ni Contents on the Microstructure and Mechanical Properties of Rapidly Solidified Mg Ribbons
p.1662
Mechanism of Crack Nucleation Analysed by In Situ Observation on Mg-Al-Zn Alloy
p.1669
The Influence of Rolling Parameters on Microstructure and Mechanical Properties of the As-Rolled AZ31 Magnesium Alloy Sheet
p.1675
Corrosion Properties of Supersaturated Magnesium Alloy Systems
p.1679
Mechanical Properties and Damping Behavior of Magnesium Alloys Processed by Equal Channel Angular Pressing
p.1685

Effect of RE Elements and Ni Contents on the Microstructure and Mechanical Properties of Rapidly Solidified Mg Ribbons

Article Preview

Abstract:

The effect of the concentration of Ni, Y and La-rich mischmetal on the thermal stability, microstructure and mechanical properties of ribbons tested in the temperature range 25-350°C have been evaluated. The low-alloyed materials were crystalline or partially crystalline while high-alloyed materials were amorphous. The amorphous alloys experienced numerous transformations during heating above 170°C. A transition in the amorphous state was observed in all alloys prior to the crystallization stage. The alloy composition determines the sequence of phase transformations during crystallization. In general, the structure of crystallised amorphous, even at high temperatures, is much finer than that of crystalline materials. A MgxREy intermetallic matrix with other intermetallic phases homogeneously distributed was observed in the crystallised ribbons with high RE contents. However, a magnesium matrix embedding other intermetallic phases was the microstructure observed for low-alloyed materials. The amorphous Mg-10Ni-2.5Y2.5-2.5La(MM) showed the higher tensile strength values up to 200 °C The crystalline Mg-2Ni-1Y-1La(MM) ribbon and the partially crystalline Mg-3Ni-1.5Y-1.5La(MM) alloy also exhibited high mechanical resistance levels which were maintained up to 250 °C. MgNi10Y2.5La(MM)2.5 amorphous and MgNi3Y1.5La(MM)1.5 crystalline broken above 500 and 400 MPa, respectively, at 100°C

You might also be interested in these eBooks
THERMEC 2006 View Preview

Info:

Periodical:

Materials Science Forum (Volumes 539-543)

Pages:

1662-1668

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.539-543.1662

Citation:

Cite this paper

Online since:

March 2007

Authors:

Sergio Gonzáles, P. Pérez, G. Garcés, P. Adeva

Keywords:

Amorphous Alloy, Magnesium Alloy, Mechanical Property, Rapid Solidification

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2007 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] T. Spassov, L. Lyubenova, U. Köster, M.D. Baró: Mat. Sci. Eng. A375-377 (2004), p.794.

Google Scholar

[2] A. Inoue: Progr. Mater. Sci 43 (1998), p.365.

Google Scholar

[3] D.V. Louzguine, A.R. Yavari, A. Inoue: J. Non. Crys. Sol. 316 (2003), p.255.

Google Scholar

[4] P. Pérez, G. Garcés and P. Adeva: J. Alloys Compd. 381 (2004), p.114.

Google Scholar

[5] P. Pérez, G. Garcés, G. Caruana and P. Adeva: Rev. Metall. Madrid, in press.

Google Scholar

[6] P. Pérez, G. Garcés, F. Sommer and P. Adeva: J. Alloys Compd. 396 (2005), p.175.

Google Scholar

[7] M.A. Torrijos, G. Garcés, J. García-Barriocanal, P. Pérez, P. Adeva: Proceedings of the PMS 2004, Spain.

Google Scholar

[8] P. Pérez, M. Eddahbi, G. Garcés, F. Sommer and P. Adeva: Scripta. Mater. 50 (2004), p.1039.

DOI: 10.1016/j.scriptamat.2003.12.025

Google Scholar

[9] G. Garcés, P. Pérez, S. González, P. Adeva: Z. Metallkd. (in press).

Google Scholar