Paper Titles
Friction and Wear Properties of Friction Stir Welds of 5052 Al Alloy
p.745
Hot Deformation Behavior of 2519 Al Alloy during Isothermal Compression
p.749
Microstructure and Grain Refining Performance of a Rapidly Solidified Al-5Ti-1B Master Alloy
p.755
Effect of Calcium Addition and Heat Treatment on the Al-Zn-In Alloys as Sacrificial Anode
p.761
Accumulative Roll-Bonding (ARB) of Sheets of Aluminium and its Commercial Alloys AA8006 and AA5754 at Ambient and Elevated Temperatures
p.767
Overview of Recent Work on Precipitation in Al-Cu-Mg Alloys
p.775
Correlation of Mechanical Properties with Defect Structure in Commercial Pure Al and Al-Mn Alloys Studied by Positron Annihilation Spectroscopy
p.783
Morphological Changes and Plume Deflection Effect during Pulsed Laser Ablation Deposition of Al
p.789
Microtexture Development and Flow Stress Saturation during Triaxial Forging of an Al-3Mg-Sc(Zr) Alloy
p.793

Accumulative Roll-Bonding (ARB) of Sheets of Aluminium and its Commercial Alloys AA8006 and AA5754 at Ambient and Elevated Temperatures

Article Preview

Abstract:

Mechanical properties and microstructure of twin-roll cast (TRC) pure aluminium, Al-Fe-Mn-Si (AA8006) and Al-Mg (AA5754) alloy sheets ARB processed at ambient and elevated temperatures (200, 250, 300 and 350°C) were investigated. Processing at elevated temperatures results in better bonding but it produces smaller increases in hardness. AA8006 specimens were processed without any problems up to 7 cycles. The alloy AA5754 suffered from severe edge and notch cracking since the first cycle. The strength was evaluated from tensile test and microhardness measurements; the microstructure was examined using light microscopy, and transmission electron microscopy. The microstructure was compared to that of conventionally cold rolled (CCR) specimens with true strain ε of 0.8, 1.6, 2.4 and 3.2 corresponding to the strain induced by 1 to 4 ARB cycles. The work hardening of alloy AA8006 saturated after the 3rd cycle, whereas the hardness of alloy AA5754 increased steadily up to the 5th cycle. Very fine grain structure with large fraction of high angle boundaries was observed in both alloys after two cycles of ARB. The grains were refined to submicrometre and nanometre size (down to 90 nm in alloy AA5754). Intensive post-dynamic recovery was observed in AA8006 specimens. The recovery is less pronounced in the AA5754 alloy with high concentration of solute atoms in solid solution.

You might also be interested in these eBooks
Progress in Light Metals, Aerospace Materials and Superconductors View Preview

Info:

Periodical:

Materials Science Forum (Volumes 546-549)

Pages:

767-774

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.546-549.767

Citation:

Cite this paper

Online since:

May 2007

Authors:

Miroslav Karlík, Margarita Slámová, Petr Homola, P. Sláma, Miroslav Cieslar

Keywords:

Accumulative Roll Bonding (ARB), Al-Fe-Mn-Si Alloy, Al-Mg Alloy, Mechanical Property, Thermal Stability, Ultrafine Grained Material

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2007 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] Y. Saito, H. Utsunomiya, N. Tsuji and T. Sakai: Acta Mater. 47 (1999) 579.

Google Scholar

[2] R.Z. Valiev, N.A. Kraslinikov and N.K. Tsenev: Mater. Sci. Eng. A137 (1991) p.35.

Google Scholar

[3] R.Z. Valiev, A.V. Korznikov and R.R. Mulyukov: Mater. Sci. Eng. 168 (1993) p.141.

Google Scholar

[4] M. Furukawa, Z. Horita, M. Nemoto, R.Z. Valiev and T.G. Langdon: Acta Mater. 44 (1996) p.4619.

Google Scholar

[5] R.Z. Valiev, R.K. Islamgaliev and I.V. Alexandrov: Prog. Mater. Sci. 45 (2000), p.103.

Google Scholar

[6] R.Z. Valiev, F. Chmelík, F. Bordeaux, G. Kapelski and B. Baudelet: Scripta Metall. Mater. 27 (1992) p.855.

Google Scholar

[7] R.Z. Abdulov, R.Z. Valiev and N.A. Krasilnikov: J. Mater. Sci. Lett. 9 (1990) p.1445.

Google Scholar

[8] J. Richert and M. Richert: Aluminium 62 (1986) p.604.

Google Scholar

[9] N. Tsuji: in: Severe Plastic Deformation, Toward Bulk Production of Nanostructured Materials, Edited by Altan, Burhanetin, Nova Science Publishers (2005) p.543.

Google Scholar

[10] Y. Saito N. Tsuji, H. Utsunomiya, T. Sakai and R.G. Hong: Scripta Mater. 39 (1998) p.1221.

Google Scholar

[11] N. Tsuji, Y. Saito, S. H. Lee and Y. Minamino: Adv. Eng. Mater. 5 (2003) p.338.

Google Scholar

[12] W. Truszkovski, J. Krol and B. Major: Metall. Trans. A, 11 (1980) p.749.

Google Scholar

[13] N. Tsuji, X. Huang and H. Nakashima: in: Evolution of Deformation Microstructure in 3D Edited by C. Gundlach et al., Risø National Laboratory, Roskilde, Denmark 2004, p.147.

Google Scholar

[14] M. Karlík, P. Homola and M. Slámová: J. Alloys Compd. 378 (2004) p.322.

Google Scholar

[15] C. P. Hearson, P. J. Apps, and P. B. Prangnell: in: Proc. of ICAA 9, Brisbane, edited by. J.F. Nie, A.J. Norton and B.C. Muddle, IMEA (2004), p.588.

Google Scholar