Paper Titles
Study on Dynamic Measurement of Thermal Stress during Solidification of a Casting Specimen
p.1841
Use of Taguchi Method to Study a Robust Design for H-Sectioned Porous Beams during Rolling
p.1845
Experimental Investigation of Isotropic and Kinematic Hardening in Al-3Cu-0.05Sn (wt%)
p.1849
The Effect of Transformation Plasticity on Prediction of Tooth Distortion of Heat-Treated Helical Gear
p.1853
Iterative Modification of Lumped Heat Capacity Method on Predicting Residual Stress and Distortion of Still-Quenched S45C Steel Cylinder
p.1857
Surface Energy of In-Doped ZnO Studied by PAW+U Method
p.1861
The Motion of Dislocation in Iron Pinning by Carbon Interstitials
p.1865
Parameter Identification of Thermal Visco-Plastic Model Considering Dynamic Recrystallization
p.1869
Effect of the Guide-Roll Positional Angle to the Stability of Radial Ring Rolling
p.1875

Iterative Modification of Lumped Heat Capacity Method on Predicting Residual Stress and Distortion of Still-Quenched S45C Steel Cylinder

Article Preview

Abstract:

Computer simulation can be utilized to predict the property and quality of heat-treated products. The prediction accuracy depends upon the thermal boundary condition and the thermal history from which surface heat transfer coefficient (HTC) is derived. Variables studied are thermal boundary and the surface HTC. Zone-based thermal boundary is set with and without edge effect. Lumped heat capacity method is used to predict HTC of silver probe (1st step), then iterative modification method is applied to the prediction of HTC of SUS304 cylinder (2nd step) and S45C cylinder itself (3rd step). Using FEM tool of DEFORM-HT combined with lumped heat program LUMPPROB, this research is intended to obtain the number of thermal boundary and iterative modification step. The higher accuracy is obtained by employing the edge effect of thermal boundary. The 2nd step significantly increases the prediction accuracy of radial distortion and residual stress distribution. However, 3rd step does not significantly increase the prediction accuracy.

You might also be interested in these eBooks
PRICM 6 View Preview

Info:

Periodical:

Materials Science Forum (Volumes 561-565)

Pages:

1857-1860

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.561-565.1857

Citation:

Cite this paper

Online since:

October 2007

Authors:

A. Sugianto, Michiharu Narazaki, M. Kogawara

Keywords:

Computer Simulation, Cylinder, Distortion, Edge Effects, Heat Transfer Coefficient (HTC), Quenching, Residual Stress

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2007 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] Joint Research Results Symposium Document, JSHT and JSMS, Kyoto, 2004, pp.41-72.

Google Scholar

[2] S. Sugisawa: Master Thesis, Utsunomiya Univ, (2005).

Google Scholar

[3] R.A. Hardin and C. Beckermann: Proc of 59th Tech and Operating Conf, SFSA, Chicago, (2005).

Google Scholar

[4] D.Y. Ju and M. Narazaki: Proc of 20th ASM-HTS Conf, (St. Louis, MO, 2000), pp.441-447.

Google Scholar

[5] M. Narazaki, G.E. Totten and G.M. Webster, in: Handbook of Residual Stress and Deformation of Steel, edited by G.E. Totten, M.A.H. Howes, and T. Inoue, ASM Intl, OH (2002), pp.248-295.

Google Scholar

[6] M. Narazaki, K. Osawa, A. Shirayori and S. Fuchizawa: Proc of 19 th ASM Heat Treating Society Conf, (Cincinnati, OH, 1999), pp.600-607.

Google Scholar

[7] DEFORM-HT (2D Ver9. 0) Users Manual, (SFTC, Columbus, OH, 2007).

Google Scholar

[8] A. Sugianto, M. Narazaki and M. Kogawara: Proc of 2nd Indonesia Japan Joint Scientific Symposium, (Jakarta, 2006), File No. IJJSS06-278.

Google Scholar

[9] S. Dennis: La Revue de Métallurgie Vol. 77 (1997), pp.158-176.

Google Scholar

[10] K. Ichitani: Proc of The 3rd Intl Conf on Thermal Process Modelling and Simulation, IFHTSE, (Budapest, 2006), File No. MOD-P3.

Google Scholar

[11] Y. Watanabe et al: Solid Sate Phenomena Vol. 118 (2006), pp.349-354.

Google Scholar