Paper Titles
Assessment of Ground Surface Roughness Based on Computer Vision Technology
p.667
Optimization Algorithm for Automated Assembly of Circular Parts
p.672
Prediction Models and Generalization Performance Study in Electrical Discharge Machining
p.677
Research on Feature-Based Rapid Programming for Aircraft NC Parts
p.682
Prediction of Residual Stress in Hard Turning of AISI 52100 Using 2D FEM
p.688
Optimization of Laser Peening Parameters Using Taguchi Method
p.692
An Integrated Modeling Method for an Engine Cylinder Body Based on Cross-Sectional Imaging System
p.697
Optimal Selection of Tool Geometry by Finite Element Simulation
p.702
Frequency Spectrum Analysis on Cutting Forces in Cutting Process
p.707

Prediction of Residual Stress in Hard Turning of AISI 52100 Using 2D FEM

Article Preview

Abstract:

Residual stress on the machined surface and the subsurface is one of the most important factors that can influence the service quality of a component, such as fatigue life, tribological properties, and distortion. In this work, a 2D FEM model of AISI 52100 hard turning processes is setup. The material properties are widely selected to describe the material property more precisely. By using user subroutine named Konti-Cut, the steady state of cutting process is simulated and the cutting forces and residual stresses in this time are investigated. By comparing the cutting forces, the FEM model can gives quite good appliance with experimental data. And the basic relations between residual stresses and cutting parameter, tool geometry are drawn.

You might also be interested in these eBooks
e-Engineering & Digital Enterprise Technology View Preview

Info:

Periodical:

Applied Mechanics and Materials (Volumes 10-12)

Pages:

688-691

DOI:

https://doi.org/10.4028/www.scientific.net/AMM.10-12.688

Citation:

Cite this paper

Online since:

December 2007

Authors:

Zhong Qiu Wang, J. Sun, Jian Feng Li, I. Al-Zkeri

Keywords:

Finite Element Model (FEM), Hard Turning, Residual Stress Prediction

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2008 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] G. Poulachot, B.P. Bandyopadhyay, I.S. Jawahir, and et al: Int. J. Mach Tool Manuf, Vol. 43 (2003), pp.139-144.

Google Scholar

[2] G. Poulachot, A.L. Moison, I.S. Jawahir: Ann. CIRP, Vol. 50 (2001) No. 1, pp.31-36.

Google Scholar

[3] H.K. Tonshoff, H. -G. Wobker, D. Brandt: Trans. NAMRI/SME XXIII (1995), pp.215-220.

Google Scholar

[4] W. Konig, M. Klinger, R. Link: Ann. CIRP, Vol. 39 (1990) No. 1, pp.61-64.

Google Scholar

[5] J. Barry, G. Byrne: Ann. CIRP, Vol. 51 (2002) No. 1, pp.65-70.

Google Scholar

[6] H. Jiang, R. Shivpuri, X.M. Cheng, and et al: Mater. Sci. and Eng. A, Vol. 394 (2005), pp.238-248.

Google Scholar

[7] J. Hua, D. Umbrello and R. Shivpuri: J. Mater. Proc. Tech, Vol. 171 (2006), pp.180-187.

Google Scholar

[8] D. Umbrello, J. Hua and R. Shivpuri: Mater. Sci. and Eng., A, Vol. 374 (2004) No. 1, pp.90-100.

Google Scholar

[9] C.R. Liu, Y.B. Guo: Int. J. Mech. Sci, Vol. 42 (2000), pp.1069-1086.

Google Scholar

[10] Y. Huang, Predictive modeling of tool wear rate with application to CBN hard turning (Ph.D. Dissertation, Georgia Institute of Technology, Georgia, USA, 2002).

Google Scholar

[11] Ramesh, Anand, Prediction of Process-Induced Microstructural Changes and Residual Stresses in Orthogonal Hard Machining (Ph.D. Dissertation, Georgia Institute of chnology, Georgia, USA, 2002).

Google Scholar

[12] Y. Guo and C.R. Liu: J. Manu. Sci. Eng, Vol. 124 (2002), pp.1-9.

Google Scholar

[13] B. Denkana and et al: Production Engineering- Research and Development (WGP) (2005).

Google Scholar

[14] F. Klocke, H.W. Raedt, S. Hoppe: J. Mach . Sci. and Tech, Vol. 5 (2001) No. 3, pp.323-340.

Google Scholar