Paper Titles
Effect of Cu Content on Microstructure and Properties of Al2O3-SiO2 Fiber Reinforced Aluminum Matrix Composites
p.873
Hot Compression Behaviour of In-Situ Synthesized (TiB+TiC)/Ti Composites Prepared by Hot-Pressing
p.877
Microstructure and Properties of a 70vol.% SiCp/Al-12Si Composite for Electronic Packaging
p.881
Influence of Strain Rate and Temperature on the Compressive Deformation of a Eutectic Al-Si Alloy Based Composite Reinforced with -Si3N4 Whisker
p.885
Microstructure and Mechanical Properties of B/Al Composite after Thermal-Mechanical Cycling
p.889
Hot Deformation Behavior of SiCw/AZ91 Magnesium Matrix Composite in Compression
p.893
Magnetoresistance of La2/3(CaxBa1-x)1/3MnO3/NiO Composite Materials
p.897
Solidification of Aluminum Infiltrated Composites
p.901
Laser Cladding Ni-Base Composite Coating on Titanium Alloy with Pre-Placed B4C+NiCoCrAlY
p.905

Microstructure and Mechanical Properties of B/Al Composite after Thermal-Mechanical Cycling

Article Preview

Abstract:

The mechanical properties of B/Al composite were measured at room temperature before and after thermal-mechanical cycling (TMC) in the temperature interval from –125°C to 125°C under constant stress of 30 MPa. The effects of TMC on microstructure and tensile fracture behavior of B/Al composite were studied by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The fiber / matrix interfaces were degraded during TMC, the extent of which was enhanced with increasing the cycles, causing a measurable decrease of stageⅠmodulus of the B/Al composite. The TMC induced the dislocation generation in the aluminum matrix and the dislocation density increased with increasing the cycles. The tensile strength of the composites increased with the cycles in the early stage of TMC, but subsequently decreased after further TMC. The interfaces in the B/Al composite changed from the strongly-bonded toward the appropriately-bonded, and then to the weakly–bonded ones with increasing the cycles.

You might also be interested in these eBooks
PRICM-5 View Preview

Info:

Periodical:

Materials Science Forum (Volumes 475-479)

Pages:

889-892

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.475-479.889

Citation:

Cite this paper

Online since:

January 2005

Authors:

Yao Chun Qin, Shi Yu He, Dezhua Dezhua

Keywords:

B/Al Composite, Mechanical Property, Microstructure, Thermal-Mechanical Cycling

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2005 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] M.D. Weisinger: Metal Process Vol. 113 (1978), p.60.

Google Scholar

[2] J.W. Brantley, R.C. Stabrylla: NASA-CR-159566 (1979), p.1.

Google Scholar

[3] T. Kamata: ICCM-IV. Tokyo (1982), p.1489.

Google Scholar

[4] E. Ozawa, I. Shiota, O. Watanabe: ICCM-IV. Tokyo (1982), p.1481.

Google Scholar

[5] M.A. Wright,: Met. Trans. Vol. 6A (1975), p.129.

Google Scholar

[6] H.H. Grimes, R.A. Lad, J.E. Maisel: Met. Trans. Vol. 8A(1977), p. (1999).

Google Scholar

[7] W.Y. Marfia: NASA-TP-1063. (1977), p.1.

Google Scholar

[8] A. Skinner, M.J. Koczak, A. Lawley: Met. Trans. Vol. 13A(1982), p.289.

Google Scholar

[9] K. Izdinsky, P. Minar, J. Ivan: Key Engineer Material Vol. 104-107(1995), p.845 (b) (a).

Google Scholar