Paper Titles
Microstructure and Properties of Ti Rods Produced by Multi-Step SPD
p.763
Mechanical Properties and Microstructure of Mg-Zn-Y Alloys Processed by ECAE
p.769
The Microstructures and Mechanical Properties of Hot-Processed Magnesium Casting Alloys
p.775
Strain Rate Sensitivity of Ultrafine Grained FCC- and BCC-Type Metals
p.781
Gradient Structure Formation by Severe Plastic Deformation
p.787
Evaluation of a Ni-20Cr Alloy Processed by Multi-Axis Forging
p.793
The Effect of the Initial Orientation on Microstructure Development of Copper Single Crystals Subjected to Equal-Channel Angular Pressing
p.799
TEM Investigations of Titanium Processed by ECAP Followed by Cold Rolling
p.805
Fracture and Fatigue Resistance of Ultrafine Grain CuCrZr Alloy Produced ECAP
p.811

Gradient Structure Formation by Severe Plastic Deformation

Article Preview

Abstract:

Severe plastic deformation (SPD) techniques are the best for producing of massive nanostructured materials. The methods of equal channel angular pressure (ECAP) and twist extrusion (TE) are realized by simple shear uniform deformation without change of cross-section sizes of sample. In the case of roll forming (RF) the shear strain is localized in the near-surface layer of metal. Intensity of shear strain in the near-surface layer depends on variation of parameters of deformation and conditions of friction in a contact. Steel 65G (0.65C, 0.3Si, 0.6Mn, 0.3Cr, and 0.3Ni) was deformed by roll forming. Transmission electron microscopy (TEM) of “cross-section” samples was used for studying of gradient structure of deformed material. TEM investigation shown that cell substructure in a near-surface layer have been formed. The depth of deformed layer is approximately 40 micrometers. Average cell size in cross-section direction is about 100 - 200 nm. Thin nanostructure layer with cell size about 20-30 nm was detected. In our opinion such substructure formed due to effect of “good” impurities.

You might also be interested in these eBooks
Nanomaterials by Severe Plastic Deformation View Preview

Info:

Periodical:

Materials Science Forum (Volumes 503-504)

Pages:

787-792

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.503-504.787

Citation:

Cite this paper

Online since:

January 2006

Authors:

M. Danylenko, Victor F. Gorban, Yu.N. Podrezov, Sergiy A. Firstov, O. Rosenberg, S. Shejkin, F. Morito, Yoko Yamabe-Mitarai

Keywords:

Microhardness, Roll Forming, Severe Plastic Deformation (SPD), TEM 'Cross-Section', True Hardness

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2006 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] G. Langford, M . Cohen,., 1969. Trans. ASM, 62, pp.623-637.

Google Scholar

[2] V. Segal, V. Reznikov, V. Kopilov, D. Pavlik, V. Malyshev, 1994. Processes of Plastic Structural Formation of Metals, Nauka i technika publishers, Minsk, p.221 (in Russian).

Google Scholar

[3] Y. Beygelzimer, V. Varyukhin, D. Orlov, B. Efros, A. Salimgareyev, V. Stolyarov, Processing and structure, Washington, 2002, pp.137-142.

DOI: 10.1002/9781118804537.ch5

Google Scholar

[4] A. W Thompson, 1977, Met. Trans. A, 7(8A), pp.833-842.

Google Scholar

[5] V. Rybin, Problems of Materials Science, 1 (29), 2002, pp.11-33. (in Russian).

Google Scholar

[6] N. Noskova, Problems of Materials Science, N 1 (29), 2002. pp.309-313. (in Russian).

Google Scholar

[7] M. Nemoto, Z. Horita, M. Furukawa, and T.G. Langdon, Materials Science forum. Vols 304-306, 1999, pp.59-66.

DOI: 10.4028/www.scientific.net/msf.304-306.59

Google Scholar

[8] A. Belotsky, A. Yurkova, Technology and product organization, N2, 1988. pp.40-43 (in Russian).

Google Scholar

[9] A. Dzubenko, A. Lapunov, I. Radomiselsky. Powder metallurgy, N9, 1986. pp.43-48.

Google Scholar

[10] S. Takaki, Materials Science Forum, Vols. 426-432, 2003, pp.215-222.

Google Scholar

[11] N. Tao, Z. Wang, W. Tong, M. Sui, J. Lu, K. Lu, 50, 2002. pp.4603-4616.

Google Scholar

[12] K. Lu, J. Lu, Mater. Sci. Eng. A 375-377, 2004, pp.38-45.

Google Scholar

[13] W. Tong, N. Tao, Z. Wang, J. Lu, K. Lu, Science, v. 299, 2003, pp.686-688.

Google Scholar

[14] O. Rozenberg, N. Novikov, S. Sheykin, M. Danylenko, Yu. Podrezov, S. Firstov, Electron Microscopy and Strength, 12, 2003, pp.25-31. (in Russian).

Google Scholar

[15] S. Firstov, T. Rogul, S. Dub, V. Svetchnicov, Proceedings of NATO Advanced Refractory Workshop on Metalic Materials with High Structural Efficiency, Kyiv, Ukraine, 7-13 September 2003, pp.341-346.

DOI: 10.1007/1-4020-2112-7_34

Google Scholar

[16] D. Tabor, The hardness of metal, Oxford Classical Series, Oxford University Press, Oxford, 2000, pp.20-66.

Google Scholar

[17] Yu. Podrezov, N. Danilenko, V. Kopylov, S. Firstov, Phys. of high pressure V. 11 N2 (2001) pp.33-45.

Google Scholar