Papers by Author: Edcleide Maria Araújo

Abstract: In this work, were obtained nanocomposite membranes polyamide66/Paraíba bentonite clay, treated with a quaternary ammonium salt in order to make it organophilic. The membranes were prepared as thin films using the technique of phase inversion from the nanocomposites obtained by solution. The membranes were characterized by X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetry (TG) and scanning electron microscopy (SEM). By means of X-ray diffractogram, it was revealed that the membranes remained organically treated clay presented exfoliated and/or partially exfoliated structure. From curves of DSC and TG, it was observed that membrane of PA66 with 3% w/w of with treatment clay showed higher thermal stability compared with the same content of clay without treatment. From the SEM photomicrographs, there was a selective layer (skin filter) on top and one porous layer at the bottom of all membranes studied. Moreover, it was verified that the presence of clay provided a significant structural modification in the membranes of polymer nanocomposites.

Abstract: Recent advances in biodegradable polymers have attracted a great interest not only in traditional areas such as biomedical and pharmaceutical industry, but also in packaging applications, articles and injected membranes. The aim of this work was to produce bio-nanocomposites poly (lactic acid) - PLA with bentonite clay. The bio-nanocomposites were produced by melt intercalation with incorporation of 1 to 3 wt% of organoclay. The degree of dispersion of clays in the polymer, and consequently the structure of bio-nanocomposites produced was evaluated by X-ray diffraction (XRD), and the thermal properties were studied by differential scanning calorimetry (DSC). XRD results indicated the formation of intercalated structures. It was observed the appearance of crystalline melting double peaks in bio-nanocomposites PLA.

Abstract: The application of polyamides is limited by low impact performance when notched in room temperature conditions. This situation is worsening, especially for use in temperatures below zero degrees Celsius. One way to outline this limitation is to prepare polymer blends where the dispersed phase is an elastomer, and then classified as an immiscible blend. Therefore, this study aims to develop polyamide 6/waste styrene-butadiene rubber (SBR) blends, with addition of compatibilizer PP-g-MA and PE-g-MA in order to achieve a balance between stiffness and tenacity. The results obtained with the rheological study showed that mixtures of PA6/PE-g-MA presented the best results in comparison with mixtures of PA6/PP-g-MA, indicating that there was probably a reaction between the components, which may allow a better dispersion and thus can achieve better properties.

Abstract: The nanocomposites are hybrid materials where at least one of the components has nanometric dimensions and in the same way as traditional composites are formed, one of the components is the matrix in which nanoparticles are dispersed. One of the possibilities of applications of nanocomposites is to obtain polymer films for applications in the barrier, or separation promoted by the dispersion of the clay lamellae. In this work, nanocomposites of nylon 6/bentonite clay were obtained by melt intercalation. The used clay was the Brasgel PA, and quaternary ammonium salt was Praepagen-HY, used in organophilization of the clay. By XRD, it was observed the disappearance of the characteristic peak of clay, and this can be facilitate the possible exfoliation of clay in the produced films from the nanocomposite. By SEM, it was observed, an apparently dense layer with no pores.

Abstract: Membranes can be defined as polymer film that acts as a semipermeable barrier to filtration in a molecular scale, separating two phases. In this work, microporous membranes were obtained from hybrid organic/inorganic polyamide66 (PA66) and clay mineral from Paraíba State, treated with a quaternary ammonium salt in order to make it organophilic. The membranes in the form of thin films were prepared by immersion-precipitation technique from the nanocomposites obtained by solution, with a pre-determined reaction time of 2 h, with characteristics suitable to be used in microfiltration process for separation of the oil present in water. Samples of natural and organophilic clay were characterized by X-ray fluorescence (XRF) and Fourier transform infrared spectroscopy (FTIR). Meanwhile, the membranes were characterized by differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). The results of FRX and FTIR confirmed the presence of quaternary ammonium salt in the clay structure after treatment with organic salt. Through DSC analysis it was observed almost no change in the melting temperature of the pure polyamide66 membranes. By SEM, it was revealed an asymmetric morphology consisting of a skin layer and a porous sublayer, showing the pore size distribution appropriated to water-oil separation.

Abstract: The development of nanocomposites polymer matrix with clay from Brazil has been naturally abundant and low cost alternative. In this study, we obtained nanocomposites polyamide66 (PA66) with 1% and 5% of bentonite clay from Brazil, to be used as microporous organic/inorganic hybrid membranes. The clay was treated with a quaternary ammonium salt in order to make it organophilic. The membranes in the form of thin films were prepared using the technique of immersion-precipitation of solution from the nanocomposites. Treated clay and untreated clay were characterized by X-ray diffraction (XRD) and Thermogravimetry (TG). The membranes were characterized by TG and XRD. The result of XRD showed the presence of quaternary ammonium salt in the structure of clay, after organophilization. For TG, we observed that the treated clay showed higher thermal stability when compared to untreated clay. For TG, we observed that in general the membranes of PA66 with treated clay, present decomposition temperature higher when compared with untreated clay, thus revealing a greater thermal stability of membranes PA66 with treated clay. Through the X-rays patterns, it was found that membranes with 1% of nanoclay present exfoliated structure and can therefore be applied as microporous membranes.

Abstract: Nanocomposites are hybrid materials that can be obtained with, three, two or bust one-dimensional in nanoscale found in particles dispersed in the matrix. By presenting a nanometric structure, this new class of materials may have only properties, different from traditional composites and their constituents, which may be established in the synthesis process. The aim of this work is prepare nanocomposites of HDPE/ bentonite clay by melt intercalation technique. Systems were evaluated for the presence of untreated clay and chemically treated (organoclay) with two different types of quaternary ammonium salts, Cetremide and Dodigen. In the preparation of nanocomposites were obtained concentrated using a high speed mixer and then the nominal percentage of clay was dispersed in a twin screw extruder corrotacional. The systems were characterized by X-ray diffraction and mechanical properties. The XRD patterns of nanocomposite of HDPE/organoclay suggest a not intercalated structure. The mechanical properties of nanocomposites presented reducing values in relation to pure polymer.

Abstract: This research is to obtain nanocomposites of HDPE/bentonite clay. Inorganic polymers reinforced with materials are of great interest due to their applications in automotive, and electrical and electronic industries. The nanocomposites were produced by melt intercalation with different percentages of clay and compared with pure HDPE. Clay was used as modified and unmodified and it was characterized by X-ray diffraction (XRD) and X-ray fluorescence (XRF). The obtained nanocomposites were characterized through thermogravimetry (TG). It was verified by XRF that clay performed compositions of bentonites characteristics. By XRD, it was observed increases basal spacing for organoclay. By TG, in general, it was verified that the nanocomposites presented greater thermal stability in relation to HDPE.

Abstract: Much attention is being given to developing nanocomposites with layered silicates, owing to the great need for advanced materials engineering and the fact that the pure polymers do not present the behavior or properties needed for certain applications within that context, the objective of this study was to influence of the molecular weight of polyamide 6 in obtaining nanocomposites with national organoclay. For this, the mixture of polyamide 6/ organoclay was processed in a twin screw extruder, and then was characterized by thermogravimetry (TG), X-ray diffraction (XRD) and heat deflection temperature (HDT). It was then possible to observe by XRD to obtain a structure exfoliated or partially exfoliated in the studied systems. For TG, it was found that the nanocomposites were stabilities higher than the pure polymer. And the values of HDT of systems were significantly higher than those of pure polyamide 6.

Abstract: This work aims to evaluate the effect of polymer content in the preparation of membranes obtained from polyamide 6/national clay nanocomposites. The polymeric membranes were produced varying the polymer content at 20 and 22% and using the technique of precipitation by immersion, which consists of three main steps: preparation a homogeneous polymer solution, scattering the solution on a surface forming a film of determined thickness and finally formation of polymeric structure of membrane by separation phases the system. The obtained results by scanning electron microscopy (SEM) indicated that the content of polymer changes the pore formation, the distribution and density, thereby obtaining membranes with different pore sizes, and it was possible to observe that the higher the polymer content, the lower will the pore diameter and more thicker will be the selective membrane layer.