Papers by Author: F. Portuese

Abstract: A process has been developed to grow multi-epy high doped structure. Trichlorosilane (TCS) and Ethylene have been used as precursor; Nitrogen (N2) and trimethylaluminum (TMA) as doping source. The SIMS and SCM analysis show that using this silicon precursor very abrupt N++/P+/N+ junctions (40-60 nm) can be obtained with low background doping concentration in a single epitaxial growth run.

Abstract: The growth rate of 4H-SiC epi layers has been increased up to 100 µm/h with the use of trichlorosilane instead of silane as silicon precursor. The epitaxial layers grown with this process have been characterized by electrical, optical and structural characterization methods. Schottky diodes, manufactured on the epitaxial layer grown with trichlorosilane at 1600 °C, have higher yield and lower defect density in comparison to diodes realized on epilayers grown with the standard epitaxial process.

Abstract: 3C-SiC/Si heteroepitaxy is hampered by large mismatches in lattice parameters (19.7%) and thermal expansion coefficient (8%) leading to 3C-SiC films containing high defects density. To reduce the presence of defects, a multi-step growth process in a CVD reactor is used. The aim of the work is to study the effect of carbonization on differently oriented Si surfaces, experiencing a 200°C-wide temperature range in a CVD reactor, to improve the crystalline quality. TEM analysis are carried out to evaluate thickness, crystal orientations and defects of carbonized layers with respect to the time-dependence of the process and to the different orientations of the Si substrate. It will be shown that process-related defects are strictly correlated to the substrate orientation either for size, density, occupied area, shape or thickness. Uniform, flat and crystalline thin SiC films are obtained with a low defect density.

Abstract: The growth rate of 4H-SiC epi layers has been increased by a factor 19 (up to 112 μm/h) with respect to the standard process with the introduction of HCl in the deposition chamber. The epitaxial layers grown with the addition of HCl have been characterized by electrical, optical and structural characterization methods. An optimized process without the addition of HCl is reported for comparison. The Schottky diodes, manufactured on the epitaxial layer grown with the addition of HCl at 1600 °C, have electrical characteristics comparable with the standard epitaxial process with the advantage of an epitaxial growth rate three times higher.

Abstract: High growth rate of 4H-SiC epitaxial layers can be reached with the introduction of HCl in the deposition chamber. The effect of the Cl/Si ratio on this epitaxial growth process has been studied by optical and electrical measurements. Optical microscopy shows an improvement of the surface morphology and luminescence measurements reveal a decrease of epitaxial layer defects with increasing the Cl/Si ratio in the range 0.05–2.0. The leakage current measured on the diodes realized on these wafers is reduced of an order of magnitude and DLTS measurements show a decrease of the EH6,7 level concentration in the same range of Cl/Si ratio. The value Cl/Si=2.0 allows to grow epitaxial layers with the lowest defect concentration.

Abstract: The influence of the epitaxial layer growth parameters on the electrical characteristics of Schottky diodes has been studied in detail. Several diodes were manufactured on different epitaxial layers grown with different Si/H2 ratio and hence with different growth rates. From the electrical characterization a maximum silicon dilution ratio can be fixed at 0.04 %. This limit fixes also a maximum growth rate that can be obtained in the epitaxial growth, with this process, at about 8 μm/h. Several epitaxial layers have been grown, using this dilution ratio, with different temperatures (1550÷1650 °C). At 1600 °C the best compromise between the direct and the reverse characteristics has been found. With this process the yield decreases from 90% for a Schottky diode area of 0.25 mm2 to 61% for the 2 mm2 diodes. Optimizing the deposition process to reduce the defects introduced by the epitaxial process, yield of the order of 80% can be reached on 1 mm2 diodes.

Abstract: 4H-SiC epitaxial layers have been grown using trichlorosilane (TCS) as the silicon precursor source together with ethylene as the carbon precursor source. A higher C/Si ratio is necessary compared with the silane/ethylene system. This ratio has to be reduced especially at higher Si/H2 ratio because the step-bunching effect occurs. From the comparison with the process that uses silane as the silicon precursor, a 15% higher growth rate has been found using TCS (trichlorosilane) at the same Si/H2 ratio. Furthermore, in the TCS process, the presence of chlorine, that reduces the possibility of silicon droplet formation, allows to use a high Si/H2 ratio and then to reach high growth rates (16 *m/h). The obtained results on the growth rates, the surface roughness and the crystal quality are very promising.

Abstract: The growth rate of 4H-SiC epi layers has been increased by a factor 3 (up to 18μm/h) with respect to the standard process with the introduction of HCl in the deposition chamber. The epitaxial layers grown with the addition of HCl have been characterized by electrical, optical and structural characterization methods. An optimized process without the addition of HCl is reported for comparison. The Schottky diodes, manufactured on the epitaxial layer grown with the addition of HCl at 1600 °C, have electrical characteristics comparable with the standard epitaxial process with the advantage of an epitaxial growth rate three times higher.