Papers by Author: Filipe Neves

Abstract: In the present study, equiatomic powder blends of Ni and Ti were mechanically activated for a short period of time in a planetary ball mill using different levels of energy input. The characterization of the mechanically activated materials was achieved by scanning electron microscopy, X-ray diffraction, differential thermal analysis and chemical analysis (oxygen and nitrogen measurements). During mechanical activation no phase transformation was induced and the high temperature reaction between Ni and Ti elemental powders was shifted to lower temperatures. Moreover, the temperature and the intensity of the exothermic reaction, i.e. the reactivity observed in the powder blends, decreased with the increase in the level of milling energy input. A maximum oxygen content of 0.39 wt% was measured after mechanical activation.

Abstract: Depending on the energy level used during mechanical alloying, the constitution of the resulting products can vary extensively. With high energy input, full transformation to the equilibrium phase, FeTi, is achieved. In contrast, for low levels of energy input, the process is akin to mixing without any phase transformation even for extended milling periods. In the present work, nanostructured FeTi powders were produced by mechanical alloying, avoiding the unfavourable agglomeration problem, by using a relatively low level of energy (e.g. 300 rpm) to mill the pure metallic constituents, Fe and Ti, followed by subsequent heat treatment at 800°C. A major achievement of this research was to show that, by modulating the milling intensity and total milling time, the high temperature synthesis reaction of FeTi (1100°C) can be partially or totally suppressed, reverting instead to a metastable reaction path at low temperature (650°C). The mechanical “activation” modifies the reactivity of the system, producing a very thin Ti /Fe layers. That in conjunction with a high level of defects induced mechanically may be responsible for the metastability. Partial substitution of Fe with Ni (10%) resulted essentially in the same phase constitution, indicating solid solution of Ni in FeTi replacing partially Fe lattice positions.

Abstract: Two promising powder metallurgy (PM) processes were used for the fabrication of NiTi shape memory alloys (SMA): Mechanically Activated Reactive FOrging Synthesis (MARFOS) and Mechanically Activated Reactive Extrusion Synthesis (MARES). In these two processes, equimolar powder mixtures of elemental Ni and Ti are first mechanically activated and then forged/extruded at relatively low temperature. Afterwards, heat treatments are used to promote homogenization and to adjust the composition of the NiTi matrix. When MARFOS and MARES processes are compared some differences have been observed but only in relation to the extent of phase transformation and to the degree of densification. The crystallite size was less than 100 nm for all the phases which indicates nanostructured materials and multi-step martensitic transformations could be observed in heat treated materials.

Abstract: This study reports the use of X-ray diffraction quantitative phase analyses in NiTi alloys produced by MARES (Mechanically Activated Reactive Extrusion Synthesis). These analyses were performed with the PowderCell 2.4 software. The mechanically activated powders heated in a DTA furnace at 500 °C had as main phases Ni (27 wt %) and Ti (30 wt %) and the major intermetallic phase was Ni3Ti (20 wt %). Above 500 °C the intermetallic phases were predominant. At 600 °C the major phase was Ni3Ti (29 wt %) and at 700 °C was NiTi2 (32 wt %). In this temperature range the NiTi was a minor intermetallic phase (14-20 wt %). No changes in the constitution or in the amount of the phases were detected between the degassed powder samples and the extruded materials. The intermetallic phases were always predominant and the major was Ni3Ti (27-32 wt %). The NiTi phase content was in a range of 15-22 wt %. The weighted residual error, Rwp, of the fittings ranged between 17 and 27. Using the Williamson and Hall plot, crystallite sizes within the range of 26-53 nm and of 12-25 nm were evaluated for the metallic and intermetallic phases, respectively. Vickers micro-hardness measurements were virtually unchanged with the extrusion parameters but increased relatively to the mechanically activated powders.

Abstract: Copper nitride films prepared by sputtering have applications such as optical data storage material, insulation barriers in micro electronic devices and coatings for mechanical applications. The present study examines nanocomposites prepared by mechanical alloying of copper with copper nitride under nitrogen atmosphere, at room temperature, in order to establish a comparison with properties of Cu-N sputtered films. The powders were consolidated into bulk samples via warm extrusion at temperatures ranging from 300 to 500°C (0.42-0.64 Tf) after encapsulation without degassing. The as-milled powders and the extruded materials were studied using X-ray diffraction, optical microscopy, scanning and transmission electron microscopy and microhardness measurements. Also, the TEM observation of the extruded sample indicates a mean grain size of about 50 nm. This evidences a higher thermal stability of the as-milled powders and the advantage of using a fast consolidation process, at a relatively low temperature. Therefore, the consolidated material did not show the dramatic softening associated with recrystallization. The consolidation of nanostructured copper-copper nitride composite powders via warm extrusion, without major grain coarsening, was demonstrated.