Papers by Author: Orest M. Ivasishin

Abstract: Titanium-based materials are attractive candidates to make low-weight armor parts. However, a broad use of titanium is limited by its high cost, especially when traditional cast and wrought technology is in place. This issue requires more economical production and improved protective properties of titanium-based materials. Powder metallurgy is a valid alternative to make products less expensive, especially when low-cost hydrogenated titanium is used instead of high-quality titanium powder. For effective protection, titanium-based armor should exhibit a substantially improved combination of hardness, strength and ductility, which can be achieved by using laminate (layered) structures. In this study, laminates based on Ti-6Al-4V (wt.%) alloy and its composites reinforced with light and hard particles of TiC and TiB were made using blended elemental powder metallurgy of hydrogenated titanium. Simplest press-and-sinter option as well as additional hot isostatic pressing were tested to achieve high set of characteristics of individual layers and laminates as a whole. It has been shown that the used reinforcement presents an exceptional opportunity for hardening of Ti-based composites without compromising their low specific weight and capable of hardness increase by more than 40% compared to the base alloy. Fabricated structures were ballistic tested and compared with open data on commercial armor made of titanium.

Abstract: Titanium matrix composites (TMCs) have found extensive application in aerospace, biomedical, and military sectors due to their exceptional strength-to-weight ratio and wear resistance at ambient and elevated temperatures. Nevertheless, conventional production methods often face a compromise between cost and performance, thus limiting the suitability of this material for broad utilization in engineering contexts. Recent research findings indicate that the utilization of manufacturing techniques such as hydrogen assisted blended elemental powder metallurgy (HABEPM) with the incorporation of a double press-and-sinter option, as well as the sintering of powder blends that have been preliminarily activated through milling, can both serve as economically viable methods for the production of highly dense TMCs with satisfactory mechanical properties. Both methods guarantee the activation of sintering in powders, resulting in notable improvements in density and a more refined and uniform microstructure compared to porous and nonuniform composites obtained through traditional vacuum sintering of powder blends. This study provides novel insights into the design and production of cost-effective and environmentally friendly TMCs with determined mechanical properties.

Abstract: High specific strength of Ti-based alloys and composites makes them highly requested materials in various structural applications, especially when lightweight is desired in high-strength constructions. When these alloys are used in layered structures, far advanced set of characteristics that combine different mechanical properties often non-compatible in a single layer uniform structure can be attained; for instance, high hardness or moduli systems are usually lacking of sufficient toughness. Mechanical properties of individual layer in multilayered materials can be controlled by changing chemical composition and microstructure within each layer specifically. In present study layered materials were formed by combination of the layer of Ti-6Al-4V alloy and metal matrix composites on its base reinforced with fine TiB and TiC particles. Structures were fabricated using blended elemental powder metallurgy (BEPM). The effect of different post-sintering thermo-mechanical treatments on structure of layered BEPM materials was studied. Processing parameters were assessed in terms of their influence on materials’ porosity, grain size and structure, distribution of reinforcement particles and layers integration. The effect of above mentioned structural characteristics on hardness of layered materials was evaluated.

Abstract: The powder metallurgy (PM) approach is widely used for cost-effective production of titanium alloys and articles. In the PM approach the large specific surface of starting powders heightens the risk of excessive impurity presence and, hence, degradation of final alloy properties. The present study analyzes the opportunity to produce sintered commercially pure titanium (CP-Ti) with acceptable impurity content from powder materials. Starting titanium and titanium hydride powders were comparatively examined. The impurity elements (oxygen, chlorine, carbon) and their conditions on the powder particle surface, as well as the surface processes and gases emitted from powders upon heating, have been analyzed by means of surface science techniques. The role of hydrogen emitted from titanium hydride in material purification has been discussed. The opportunity to produce titanium materials with final admissible content of interstitials (O, C, Cl, and H) using starting titanium hydride powder has been demonstrated.

Abstract: Two near-β alloys, Ti-5Al-5Mo-5V-2Cr-1Fe and Ti-10V-3Fe-3Al, were produced by the blended element powder metallurgy technique. The use of (i) elemental powders with the Al-V master alloy in the case of Ti-5Al-5Mo-5V-2Cr-1Fe and, (ii) the complex Al-Fe-V master alloy in Ti-10V-3Fe-3Al has highlighted the influence of different alloying elements and their combination on microstructure evolution and chemical homogenisation. While Fe has the fastest diffusivity in Ti and its addition improves the density of both sintered alloys it also results in accelerated rates of grain coarsening. The combination of Al and V in the master alloy powder inhibits the diffusion of V into the Ti matrix. The unexpectedly slow diffusion of Cr at the early sintering stage in Ti-5Al-5Mo-5V-2Cr-1Fe was attributed to the formation of surface oxides on the Cr powders.

Abstract: High strength near-beta titanium alloys are being increasingly used in industry due to their excellent combination of properties. Blended elemental powder metallurgy (BEPM) allows to produce the above alloys and parts from them in a cost-effective manner. However, the alloy synthesis is complicated by a big amount (up to 18 wt.%) of alloying elements which diffusional redistribution between alloying particles and titanium matrix has a strong impact on microstructure evolution. In this paper synthesis of the high-strength alloys from the powder blends based on hydrogenated titanium was studied. It was found that hydrogen strongly affects diffusion controlled processes upon synthesis, such as chemical homogenization, densification and grain growth through its influence on phase composition and defect structure of the blends. Optimization of the processing parameters allowed to produce uniform, nearly-dense alloys with reduced grain size, which mechanical properties met the requirements of corresponding specifications.

Abstract: In the present study titanium alloys were synthesized by the blended elemental press-andsinter powder metallurgy approach using hydrogenated titanium powder. Experimental investigation and modeling of the homogenization processes during synthesis were used to analyze peculiarities of mass transfer and factors affecting diffusion. Processes of alloying elements redistribution during chemical homogenization of powder blends are shown to be strongly dependent on the chemical composition of the initial powders. Optimization of the processing parameters allows to synthesize uniform, nearly-dense material with reduced grain size, at relatively low temperatures and short time. This will provide improvement of mechanical properties simultaneously with better cost-effectiveness of the process.