Papers by Author: Tei Saburi

Abstract: The dynamic strain distribution behavior of a mortar block blasting was experimentally investigated. A small-scale blasting experiment using a mortar block with well-defined property was conducted and the dynamic strain distribution on the mortal block surface was analyzed using a Digital Image Correlation (DIC) method to establish the effective method for investigating the relationship between blast design and fracture mechanism. The block was blasted by simultaneous detonation of Composition C4 explosive charges with an electric detonator in two boreholes. The behavior of the block surface was observed by two high-speed cameras for three-dimensional DIC analysis and it was also measured by a strain-gauge for comparison. The three-dimensional displacements of the free surface of the block were obtained and dynamic strain distributions were computed. A point strain profile extracted from the analyzed strain distribution data was compared with a directly observed strain profile by the strain gauge.

Abstract: Nitrocellulose (NC) is known to undergo spontaneous ignition, and its thermal stability has been previously reported to decrease in the presence of sulfuric acid. In this study, we evaluated the decomposition and ignition behavior of NC in the presence of sulfuric acid using an accelerating rate calorimeter (ARC) and hand-built ignition testing equipment. The results of the ARC experiment indicated that the thermal stability of NC decreased when the amount of sulfuric acid was increased above 10^-5 mol/g (NC). In addition, when NC (4 g) mixed with sulfuric acid (6.6 mol/L, 1 g) was isothermally stored at 75°C in a glass flask, the color of the reaction mixture changed from white to brown. After 83–127 min, NC spontaneously ignited and produced a loud explosion.

Abstract: In order to know accurate information on the non-ideal detonation pressure, steel tube test was carried out on ammonium nitrate (AN) and activated carbon (AC) mixtures. In this test, detonation velocity and pressure were measured simultaneously by varying thickness of PMMA placed between AN/AC and pressure gauge. The length and the diameter of the steel tube were 350 mm and 35.5 mm. The results showed that shock pressure attenuation in PMMA was not observed for this experimental condition (PMMA gap; 3-5 mm). The averaged measured peak pressure and detonation velocity were 3.4 GPa and 3.2 km/s.

Abstract: A multidimensional analysis code for reactive shocks (MARS), which is developed to solve various problems in the physical hazard analysis of high energetic materials, has been applied to such complex problems as multi-material problem and sympathetic problem because it can employ various types of equations of state and a materials database. However, it was difficult to meet a growing demand for large-scale analysis and fluid-structure interaction (FSI) analysis. To address these issues, this study reports a parallelization of the code and an implementation of the functional capability of FSI analysis, and performance results for sample problems were also shown.

Abstract: The relationship between the initial temperature dependence of the detonation velocity and the initial density is examined using a proposed unified form of the EOS for pentaerythritol tetranitrate (PETN). First, the derivatives of the variables at Chapman-Jouguet (C-J) points are calculated. These derivatives are used to investigate the initial state dependence of the detonation velocity using the relationship between the detonation velocity and the initial state variables. As a result, the contributions of the coefficient of thermal expansion and the increment of the initial internal energy to the detonation velocity are clarified. We found that the initial temperature derivative of the detonation velocity can be estimated from the initial density derivative of the detonation velocity.

Abstract: In this study, a high strain rate test method of a steel plate under blast loading from high explosive was designed and was conducted by a combined experimental/numerical approach to facilitate the estimation process for the dynamic stress-strain curve under practical strain rate conditions. The steel plate was subjected to a blast load, which was generated by Composition C4 explosive and the dynamic deformation of the plate was observed with a high-speed video camera. Time-deformation relations were acquired by image analysis. A numerical simulation for the dynamic behaviors of the plate identical to the experimental condition was conducted using a coupling analysis of finite element method (FEM) and discrete particle method (DPM). Explosives were modeled by discrete particles and the steel plate and other materials were modeled by finite element. The blast load on the plate was described fluid-structure interaction (FSI) between DPM and FEM. As inverse analysis scheme to estimate dynamic stress-strain curve, an evaluation using a quasistatic data was conducted. In addition, two types of approximations for stress-strain curve were assumed and optimized by least square method. One is a 2-piece approximation, and was optimized by least squares method using a yield stress and a tangent modulus as parameters. The other is a continuous piecewise linear approximation, in which a stress-strain curve was divided into some segments based on experimental time-deformation relation, and was sequentially optimized using youngs modulus or yield stress as parameter. The results showed that the piecewise approximation can gives reasonably agreement with SS curve obtained from the experiment.

Abstract: The purpose of this study is to reconstruct the equation of state (EOS) whose parameters can be applied for high energetic material of arbitrary initial density without any modification. The simulation for detonation propagation in arbitrary initial density was proposed as the new method for obtaining the information of the EOS for detonation products of arbitrary initial density. At the same time, to collect the experimental data which verify the applicability of the numerical simulation, the detonation velocity for the system consisting of the pellet explosives and air gaps were conducted. The thickness of the 20 mm diameter pellet explosive was 10 mm, and air gaps were varied 0.5 mm to 2.0 mm. The relationship between detonation velocity and experimental condition was clarified for composition A5. The proposed one dimensional simulation was also conducted. The relationships between the pressure and the specific volume for detonation products were extracted from the proposed simulation

Abstract: In order to investigate the hazard of the fragments caused by the explosion damage, the simply-simulated explosion experiment and numerical simulation were conducted. In this study, the behavior of the disk supposing the fragment driven by an explosive was investigated. In the experiment, the optical observation using a high-speed camera was performed to obtain the basic data about a disk, such as flying velocity. Moreover, numerical simulation was performed using analysis software LS-DYNA. Comparison and examination for experimental results and numerical results were reported.

Abstract: The development study of blast containment vessels for anti-terrorism has been conducted. The goal of this study is to develop safe disposal vessel for 10 kg of explosives. Considering of the use at the airport or railroad stations, it needs to be more compact compared with the conventional explosion chamber. By introducing both the internal structure and attenuation technology in the vessel, sufficient blast proof ability to contain internal explosion is realized. The blast containment vessel can be used repeatedly by exchanging the internal structure. To realize these concepts, model experiments were carried out using high speed photography, strain and pressure measurements. By introducing these technologies, the vessel for the 1 kg of explosive materials has been made, and the experiments employing 1 kg C4 explosive have been conducted. Finally, the compact blast containment vessel for 10 kg explosives was made, and its blast proof ability was shown by the internal blast test.

Abstract: This paper presents the design of a compact size projectile accelerator, and its application. To meet the various needs such as a compact body size to use under various experimental conditions, an easy maintenance for repetitive experiments during a certain period, and a capability of the velocity control, the compact accelerators were newly designed with a direct explosive drive method. Two different types of accelerator were designed: a PMMA accelerator and a metal accelerator. The pictures of the projectile shoot using the designed accelerators were recorded by SHIMADZU HyperVision HPV-1 high-speed video camera. As a result, it was recognized that the PMMA accelerator was failed to accelerate the projectile, while the metal accelerator succeeded to accelerate it effectively. The accelerating performance of the metal accelerator was further investigated. The explosives for projectile acceleration were Emulsion explosive and Composition C4 explosive weighing 5 to 35g. It was found that the metal accelerator has the capability to control the projectile velocity adjusting the weight of the explosives, and there is an approximate linear correlation between them in our experimental range. A series of impact tests on 5052S aluminum alloy targets was examined using the accelerator.