Papers by Author: Wei Xu

Abstract: Multi-pass of equal channel angular pressing (ECAP) at a single temperature as low as room temperature from 200 °C were measured using electronic back scatter diffraction (EBSD). The effect of texture and grain size on mechanical properties was investigated to realize the strengthening and large plastic deformation mechanism. A room temperature ECAP with multi-pass procedure is effective to product high strength and large plastic Mg, as a result of submicron grain structure and texture strengthening.

Abstract: A two-phase Ti-Al material was fabricated by severe plastic deformation. Particles of finely mixed elemental Ti and Al were mechanically milled and then consolidated by equal channel angular pressing. The bulk material has a unique interpenetrating structure of Ti and Al phases with multiple scales from micro to nano. Compared to its coarse structured counterpart, the multiscale structured material exhibited a significant increase in strength without compromising plasticity.

Abstract: Mechanically milled pure aluminium powders were fabricated into bulk materials using back pressure equal channel angular consolidation (BP-ECAC) for four or eight passes at 373K. The bulk materials consolidated from 0 h and 4 h mechanically milled powders were characterised by Vickers hardness tests and density measurements. Thermal stability of the consolidated bulk materials was evaluated by isothermal heat treatments at 673K. The as-consolidated bulk material from the 0 h milled (i.e. unmilled) powder showed nearly full density. However, full density was not obtained with the 4 h milled powder even after eight passes. The HV values for the as-consolidated materials fabricated from the 0 h and 4 h milled powders after four passes and from the 4 h milled powder after eight passes were 57, 121 and 136, respectively. Softening was observed in the bulk material consolidated from the 0 h milled powder during the isothermal heat treatment. However, the hardness of the bulk materials consolidated from the 4 h milled powders after four and eight passes increased to maximum values of 137 and 141 after heat treatment for 28 h and 8 h at 673K, respectively. The maximum hardness was maintained for up to 100 h at 673K in both materials. The hardening and thermal stability in the bulk materials from the milled powders are attributable to dispersion strengthening of Al4C3 particles formed by solid-state reaction during the isothermal heat treatment.

Abstract: Severe plastic deformation (SPD) has received considerable attention for its capability to produce ultrafine and nano structured materials. On the one hand, SPD, especially in the forms of equal channel angular pressing (ECAP) and high pressure torsion (HPT) is able to refine bulk materials with coarse grain structures. On the other hand, SPD has been used to synthesise bulk materials from particles. It enables particles from nano to micro scales to be consolidated into fully dense materials at much lower temperatures and shorter times, compared to the conventional sintering processing. It is particularly relevant to consolidating particles with non-equilibrium microstructures and to producing complex multiphase alloys. In this summary, ECAP as an effective process to synthesise a range of light metal based materials from particles with various sizes and structures, including aluminium and aluminium composites, titanium and magnesium, will be demonstrated. Full density and good bonding are achieved easily with the application of a back pressure. Microstructures from nano to ultrafine scales have been produced, resulting in significantly enhanced strength. Simultaneous increase in ductility has also been achieved in some alloys by virtue of multi-scale structures.

Abstract: Bulk magnesium was consolidated from pure Mg particles with an average size of ~59 µm by back pressure equal channel angular pressing. The Mg powder was processed at 200°C for 4 and 8 passes, respectively, using route C. The consolidated materials displayed density of 1.78 g/cm3, compared to the theoretical value of 1.74 g/cm3 for pure Mg. Vickers microhardness (HV) values were measured to be about 54. Compressive tests at room temperature revealed yield strengths of 100-110 MPa and ultimate strengths of up to 142 MPa with strains to fracture of ~9%, comparable to those for extruded pure Mg. Microstructures were examined using optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM).

Abstract: Back pressure equal channel angular (BP-ECA) processing was utilised to consolidate a dehydrided (DH) Ti powder of high interstitial content (1.15 wt.% O, 0.09 wt.% N) at 630°C into fully dense bulk ultrafine-grained (UFG) Ti. The consolidated samples showed an increase in the contents of oxygen (1.34 wt.%) and nitrogen (0.3 wt.%). The measured densities of 4.53 g/cm3 for the consolidated samples after 1 and 3 passes were very close to the theoretical value of pure Ti. TEM revealed the formation of a bimodal microstructure in the one-pass sample, comprising equiaxed grains of several micrometers in size with ultrafine grains of the order of 100 nm uniformly distributed at the triple grain junctions. Most grains had high-angle grain boundaries with some boundaries exhibiting non-equilibrium characteristics. Upon further BP-ECA processing to three passes, the micrometer-sized grains were refined down to the ultrafine level and copious nanoscale deformation twins were introduced by severe plastic strain into those ultrafine grains of the order of 100 nm. As a result of high interstitial contents and refined grains, the sample after processing for 3 passes exhibited remarkably enhanced true yield and ultimate strengths of 1510 and 2050 MPa, respectively. Significantly, a noticeable compressive ductility was simultaneously attained despite such a high interstitial content, thanks probably to the non-equilibrium grain boundaries, bimodal grain structure and the occurrence of deformation twinning.