Papers by Author: Xin Tang

Abstract: The influence of W and Al on the solidus and liquidus temperatures, microstructure and stress-rupture property at 980 °C/250 MPa was investigated in three Re-free experimental Ni-based single crystal superalloys. The results indicated that the solidus temperature increased for 14.0 °C and 9.8 °C by adding 0.84 wt.% W only and adding 0.45 wt.% Al and 0.44 wt.% W to the base alloy, respectively. The γ′ morphology changed from nearly cuboidal in the base alloy to cuboidal by adding 0.45 wt.% Al and 0.44 wt.% W. The volume fraction of γ′ precipitates increased, while the γ channel width decreased after adding Al and W. The additions of Al and W improved the stress-rupture life at 980 °C/250 MPa because of higher γ′ volume fraction, narrower γ matrix channel and more complete rafting structure.

Abstract: In this work, the physical aging and its effect on nonlinear creep behavior of poly(methyl methacrylate) are presented. After annealing above Tg to release the previous thermal and stress history, the samples were quenched to 60oC, aged for various times, and were then tested at three different stress levels (22MPa, 26MPa and 30MPa) at room temperature of 27oC. At each stress level, the creep strain was converted to compliance and measured as a function of test time and aging time. The test results show that higher stress accelerates creep rate of the material while physical aging plays a reverse role. The time-aging time superposition is applicable to build a master creep compliance curve at each stress level, and it is demonstrated that the shift rate deceases with increasing stress. Moreover, based on the time-stress superposition principle, a unified master curve was constructed by further shifting the sub-master curves at 30MPa and 26 MPa to a reference stress level of 22MPa.

Abstract: Temperature induced change, and stress induced change as well, in intrinsic timescale were investigated by nonlinear creep tests on poly(methyl methacrylate). With four different experimental temperatures, from 14 to 26 degrees centigrade, time-dependent axial elongations of the specimen were measured at seven different stress levels, from 14 MPa to 30 MPa, and modeled according to the concept of time-temperature-stress equivalence. The test duration was only 4000 seconds. The corresponding temperature shift factors, stress shift factors and temperature-stress shift factors were obtained according to the time-temperature superposition principle (TTSP), the time-stress superposition principle (TSSP) and the time-temperature-stress superposition principle (TTSSP). The master creep compliance curve up to about two-year at a reference temperature 14 degrees centigrade and a reference stress 14 MPa was constructed by shifting the creep curves horizontally along the logarithmic time axis using shift factors. It is shown that TTSSP provides an effective accelerated test technique in the laboratory, the results obtained from a short-term creep test of PMMA specimen at high temperature and stress level can be used to construct the master creep compliance curve for prediction of the long-term mechanical properties at relatively lower temperature and stress level.

Abstract: The mechanical behaviors were investigated by nonlinear creep tests of poly(methyl methacrylate) under different temperatures. The test duration was 4000 seconds. The corresponding temperature shift factors, stress shift factors and temperature-stress shift factors were obtained according to time-temperature superposition principle, the time-stress superposition principle and the time-temperature-stress superposition principle (TTSSP). The master creep compliance curve up to about 1-month at a reference temperature 22 degrees centigrade and a reference stress 14 MPa was constructed, and the effect of stress-induced damage evolution on the long-term creep behavior of polymeric material was accounted. It was shown that TTSSP provides an effective accelerated test technique in the laboratory, the results obtained from a short-term creep test of poly(methyl methacrylate) specimen at high temperature and stress level can be used to construct the master creep compliance curve for prediction of the long-term mechanical properties at relatively lower temperature and stress level, and the master creep compliance curve with damage considered can be applied to accurately characterize the long-term creep behavior of nonlinear viscoelastic polymer.