Papers by Author: Young Geun Lee

Abstract: Manganese silicide is one of the potential thermoelectric materials for high temperature application. As a fundamental investigation on these materials group, manganese monosilicides were synthesized by the mechanical alloying of stoichiometric elemental powder compositions, and the as-milled powders were consolidate by vacuum hot pressing. Phase transformation and microstructure evolution during mechanical alloying and hot consolidation were investigated using XRD and SEM. Near single phase of monosilicides were successfully produced in this process. Thermoelectric properties as a function of temperature were evaluated in terms of Seebeek coefficient, electrical resistivity, thermal conductivity and the figure of merit for the hot pressed specimens. Mechanically alloyed manganese monosilicide, MnSi, appeared to have a potential as a thermoelectric material in this study.

Abstract: Half-Heusler alloys are one of the potential thermoelectric materials for medium to high temperature range application. As a part of fundamental study to establish processing route and to observe thermoelectric properties in undoped state, ZrCoSb was selected, processed and evaluated. In an attempt to produce a half-Heusler thermoelectric materials having ultra fine grain structures, ZrCoSb was synthesized by mechanical alloying of stoichiometric elemental powder compositions, and consolidated by vacuum hot pressing. Phase transformations during mechanical alloying and hot consolidation were investigated using XRD, SEM and EDS. Single-phase, half-Heusler was successfully produced by vacuum hot pressing using as-milled powders without subsequent annealing. Thermoelectric properties as functions of temperature were evaluated in terms of Seebeek coefficient, electrical conductivity, thermal conductivity and the figure of merit for the hot pressed specimens. Mechanically alloyed half-Heusler phase, ZrCoSb, appeared to have a great potential as a thermoelectric materials in this study.

Abstract: Hydrogen energy had recognized clean systems and high energy carrier. Mg and Mg-based materials have been lightweight and low cost materials which had been 7.6wt.% hydrogen capacity. However, Mg and Mg-alloys were currently hinder by its high absorption/desorption temperature, and very slow reaction kinetics. Therefore, one of the most methods to improve kinetics focused on addition transition metal oxide. Addition to transition metal oxide in MgH_x powder produce MgH_x-metal oxide composition by mechanical alloy and it analyze XRD, EDS, TG/DSC, SEM, and PCI. This report considers kinetics by transition metal oxide rate and hydrogen pressure. In this research, we can see behavior of hydriding/dehydriding profiles by addition catalyst (transition metal oxide). MgH_x-5wt.%Fe₂O₃ composite was measured most high hydrogen capacity and fast kinetics.

Abstract: The effect of AgSbO₃ on the piezoelectric properties of (K_0.5Na_0.5)_0.95Li_0.05NbO₃ was examined. The AgSbO₃ doped KNLN samples sintered at 1050°C showed the maximum values of the sintering density of 4.56 g/cm³ compared to un-doped KNLN samples sintered at same temperature with 4.25 g/cm³. Moreover, the addition of AgSbO₃ enhanced the piezoelectric and dielectric properties. Piezoelectric constant (d₃₃), the planar electromechanical coupling factor (k_p) and the relative dielectric permittivity (K₃₃^T) increased up to 230pC/N, 43.5%, 1080, respectively, with addition of AgSbO₃.

Abstract: Recent search for novel thermoelectric materials has revealed a new class of compounds with half-Heusler structure as good candidates for higher performance thermoelectric conversion [1-2], since the structure was first found [3]. The unit cell of the half-Heusler with a space group F4¯ 3m consists of 4 interpenetrating cubic lattices. The crystallographic sites (0,0,0) and (1/4, 1/4, 1/4) are occupied by two different transition metals, the (1/2, 1/2, 1/2) site is occupied by Sn, Sb, or Bi, and the site (3/4, 3/4, 3/4) is empty [4,5]. Candidates with this structure for the investigation would be categorized into the combination of (Ti/Zr/Hf)(Co/Ni/Pt)(Sb/Sn/Bi) [4-6].

Abstract: 0.03Pb(Sb0.5Nb0.5)O3-0.03Pb(Mn1/3Nb2/3)O3-(0.94-x)PbTiO3-xPbZrO3 ceramics doped with Y2O3 were synthesized by conventional bulk ceramic processing technique. Phases analysis, microstructures and piezoelectric properties were investigated as a function of Y2O3 contents (0.03, 0.05, 0.1 0.3, 0.5 and 0.7 wt.%). Microstructures and phases information were characterized using a scanning electron microscope (SEM) and an X-ray diffractometer (XRD). Relative dielectric constant (K33 T) and coupling factor (kp) were obtained from the resonance measurement method. Both K33 T and kp were shown to reach to the maximum at 0.1wt.% Y2O3. In order to evaluate the stability of resonance frequency and effective electromechanical coupling factor (Keff) as a function of Y2O3 contents under strong electric field, the variation of resonance and anti-resonance frequency were also measured using a high voltage frequency response analyzer(FRA5096) under various alternating electric fields from 10V/mm to 80V/mm. It was shown that the effective electromechanical coupling factor was stabilized along with increasing Y2O3 contents.

Abstract: Undoped CoSb3 powders were synthesized by mechanical alloying of elemental powders using a nominal stoichiometric composition. Nanostructured, single-phase skutterudite CoSb3 was successfully produced by vacuum hot pressing using as-milled powders without subsequent annealing. Phase transformations during synthesis were investigated using XRD, and microstructure was observed using SEM and TEM. Thermoelectric properties in terms of Seebeck coefficient, electrical conductivity, thermal conductivity and figure of merit were systematically measured and compared with the results of analogous studies. Lattice thermal conductivity was reduced owing to increasing phonon scattering in nanostructured CoSb3, leading to enhancement in the thermoelectric figure of merit. Mechanical Alloying associated with vacuum hot pressing technique offers an alternative potential processing route for the production of skutterudites.

Abstract: Zn4Sb3 was successfully produced by a hot pressing technique, and its thermoelectric properties were investigated in the temperature range from 4K to 300K. The Seebeck coefficient, electrical conductivity, thermal conductivity, and thermoelectric figure of merit showed a discontinuity in variation at 242K, indicating the α-Zn4Sb3 to β-Zn4Sb3 phase transformation. Lattice thermal conductivity was found to be dominant in the total thermal conductivity of Zn4Sb3. Therefore, it is expected that thermoelectric properties can be improved by reducing the lattice thermal conductivity inducing phonon scattering centers.

Abstract: To enhance high power characteristics for piezoelectric transformer, an alloy design approach in PZT base ceramic system was considered. Various Zr/Ti ratio compositions in 0.03Pb(Sb0.5Nb0.5)O3- 0.03Pb(Mn1/3Nb2/3)O3-(0.94-x)PbTiO3-xPbZrO3 (0.445
x
0.475 mol)[PSN - PMN - PZT] system were synthesized by the conventional bulk ceramic processing technique. To improve high power characteristics at their morphotropic phase boundary (MPB) composition of PSN-PMN-PZT system, various spectra of Zr/Ti ratio were systematically experimented, and their effects on the subsequent piezoelectric properties and dielectric properties for high power piezoelectric transformer application were investigated using an impedance analyzer and a laser vibrometer. Microstructure and phase information were characterized using X-ray diffractometer (XRD) and a scanning electron microscope (SEM). When the Zr/Ti ratios were 0.475/0.465, the mechanical quality factor and electromechanical coupling factor were shown to reach the maximum, indicating that this alloy design can be a feasible composition for high power transformer.

Abstract: In an approach to acclimate ourselves to the recent ecological consciousness trends, a lead free piezoelectric material, bismuth sodium barium titanate (Bi0.5Na0.5)0.94Ba0.06TiO3 (BNBT), was considered as an environment-friendly alternative to the PZT system. A perovskite BNBT was synthesized by the conventional bulk ceramic processing technique.
La2O3 as a dopant was incorporated into the BNBT system up to 0.025 mol, and the doping effects on subsequent piezoelectric and dielectric properties were systematically investigated. In the case of La2O3 addition, the formation of grain boundary coherency was remarkably increased, and the sintered density was increased with increasing La2O3 contents. Piezoelectric and dielectric properties were shown to have the maximum value at 0.02 mol of La2O3 addition. La3+ ions were believed to act as a softener in the BNBT system and to enhance dielectric and piezoelectric properties in this study.