Papers by Keyword: Bulk Glassy Alloy

Abstract: Zr-based bulk glassy (BG) alloys show high tensile strength and a high Charpy impact value. In this study, the free volume changes for the hypoeutectic Zr60Cu30Al10 BG alloy during isothermal annealing below glass transition temperature (Tg) have been investigated by positron annihilation lifetime and coincidence Doppler broadening (CDB) measurements. The positron lifetime of hypoeutectic and eutectic BG alloys is almost the same, although the atomic volume ratio, estimated by the density for the eutectic BG alloy is different from that for the hypoeutectic BG alloy. The CDB spectra show a marked difference between eutectic and hypoeutectic BG alloys; that is, the spectrum of the hypoeutectic BG alloy is closes to that of Zr metal than that of the eutectic BG alloy. This result exhibits that the elemental fraction of Zr atoms around free volume in hypoeutectic BG alloy is greater than that in eutectic BG alloy. The CDB ratio profiles for the hypoeutectic BG alloy during annealing shows no appreciable change. The same trend was observed in the eutectic BG alloy.

Abstract: The degree of amorphousness of the cast glassy sample is evaluated by free volume, which can be roughly estimated by density. The glass structural difference of cast glassy samples is mainly originated to the difference of those cooling rates. In order to clarify the degree of amorphousness, we use the volume change during annealing just below glass transition temperature (Tg) in this study. Therefore the volume change has close relation with free volume. We tried to control the excess free volume in Zr-TM-Al (TM: Cu, Ni and Co) bulk glassy alloys (BGAs) using small additive element. We found the elements; Pd, Ag, Pt and Au, whose outer d-electrons are filled up, are effective to increase the volume change/free volume in Zr-Cu-Al BGAs. The relationship between the Young’s modulus and volume change indicates the existence of two groups. The difference between them might be originated to the difference in glass structures.

Abstract: This paper reviews our recent results of the formation, fundamental properties, workability and applications of late transition metal (LTM) base bulk glassy alloys (BGAs) developed since 1995. The BGAs were obtained in Fe-(Al,Ga)-(P,C,B,Si), Fe-(Cr,Mo)-(C,B), Fe-(Zr,Hf,Nb,Ta)-B, Fe-Ln-B(Ln=lanthanide metal), Fe-B-Si-Nb and Fe-Nd-Al for Fe-based alloys, Co-(Ta,Mo)-B and Co-B-Si-Nb for Co-based alloys, Ni-Nb-(Ti,Zr)-(Co,Ni) for Ni-based alloys, and Cu-Ti-(Zr,Hf), Cu-Al-(Zr,Hf), Cu-Ti-(Zr,Hf)-(Ni,Co) and Cu-Al-(Zr,Hf)-(Ag,Pd) for Cu-based alloys. These BGAs exhibit useful properties of high mechanical strength, large elastic elongation and high corrosion resistance. In addition, Fe- and Co-based glassy alloys have good soft magnetic properties which cannot be obtained for amorphous and crystalline type magnetic alloys. The Feand Ni-based BGAs have already been used in some application fields. These LTM base BGAs are promising as new metallic engineering materials.

Abstract: Recent development of corrosion resistant bulk glassy alloys such as Zr-, Fe-, Ni- and Cu-base alloys were presented. It was clarified that the enrichment of cations in the passive film, which is responsible to corrosion resistance, depends on both alloy composition and environment. TEM observation also made it clear that alloys lose their advantageous properties such as corrosion resistance when they are devoid of or lose amorphous structure even in part due to low glass forming ability or heating. These findings were essentially similar to those of conventional amorphous alloys.