Papers by Keyword: Q-P Process

Abstract: Ballistic steels are used for the basic ballistic protection of armoured vehicles against the compressive energy of exploding munitions and the impact energy of projectiles fired from small arms. Steels with hardness up to 500 HBW are used to protect the chassis of armoured vehicles. Steels with a hardness greater than 500 HBW are used to protect the cabs and turrets of armoured vehicles. Ballistic steels belong to the class of low alloy high strength steels where a good combination of high strength and toughness is required. Higher strength is achieved in the final production process which involves heat treatment by quenching and tempering. This treatment creates a martensitic structure. Another heat treatment option is the Q-P (quenching and partitioning) process, where higher material strengths can be achieved in some steels while maintaining ductility. This paper focuses on a comparison of the microstructure as observed using a light microscope of the ballistic steel Secure after heat treatment by the manufacturer and after heat treatment by the Q-P process. It was found that the Q-P process produces a finer grained structure and a change in mechanical properties due to the stabilised austenite and strained martensite in the microstructure of the ballistic steel.

Abstract: A refined microstructure consisting of martensite and retained austenite at room temperature has been produced in a Nb-microalloyed low carbon Si-Mn steel by a novel heat-treatment, pre-quenching prior to quenching and partitioning processes (Q&Q-P). The results showed that compared with the conventional quenching and partitioning steel the mechanical properties of steel obtained by the novel treatment have been significantly improved, with a good combination of ultimate tensile strength (1000MPa) and total elongation (above 30%). Meanwhile, the volume fraction of retained austenite has been increased. It was found that the improvement of mechanical properties was mainly attributed to the enhanced TRIP effect due to the relatively high fraction of metastable retained austenite at room temperature. The increased stability of austenite results from the C and Mn partitioning during inter-critical annealing, which increased the chemical stability of austenite. The formation of refined austenite at inter-critical annealing also had a positive effect on the stability of the austenite. As a consequence, the volume fraction of retained austenite at room temperature was significantly increased. Compared with the Q-P steel, the Q&Q-P steel exhibited higher work hardening exponents during the stage of TRIP effect and had the higher ductility.

Abstract: The use of the combined influence of retained austenite and bainitic ferrite to improve strength and ductility has been known for many years from the treatment of multiphase steels. Recently, the very fine films of retained austenite along the martensitic laths have also become the centre of attention. This treatment is called the Q-P process (quenching and partitioning). In this experimental program the quenching temperature and the isothermal holding temperature for diffusion carbon distribution for three advanced high strength steels with carbon content of 0.43 % was examined. The alloying strategies have a different content of manganese and silicon, which leads to various martensite start and finish temperatures. The model treatment was carried out using a thermomechanical simulator. Tested regimes resulted in a tensile strength of over 2000MPa with a ductility of above 14 %. The increase of the partitioning temperature influenced the intensity of martensite tempering and caused the decrease of tensile strength by 400MPa down to 1600MPa and at the same time more than 10 % growth of ductility occurred, increasing it to more than 20%.

Abstract: The concepts new types of materials are, for economic reasons, focused mainly on low alloyed steels with a good combination of strength and ductility. Suitable heat and thermo-mechanical treatments play an important role for the utilization of these materials. Different alloying strategies are used to influence phase transformations. The quenching and partitioning process (Q-P Process) is one of the heat treatment methods which can result in a high ultimate strength as well as a good ductility. However, these good properties can be obtained only if a sufficient amount of retained austenite is stabilized. The influence of different contents of manganese, silicon and chromium on microstructural development and mechanical properties were experimentally tested. Alloying elements were used to stabilize the retained austenite in the final microstructure and also to strengthen the solid solution. Ultimate strengths of over 2000MPa with ductility over 10% were reached after the optimization of the Q-P Process. The microstructures were analyzed using several microscopic methods; mechanical properties were determined by a tensile test and the volume fraction of the retained austenite was established by X-ray diffraction phase analysis.