Papers by Keyword: RFPA

Abstract: The special advantages of Soundless Crack method are safety and environmental protection. Soundless Crack is widely used in stone exploitation, partly crack of brittleness materials such as rock and concrete, and backout of building in city. In these engineering, we must drill many holes for loading Soundless Cracking Agents, but the drilling cost is expensive including human cost and materials cost, at the same time need much time to drill these holes. So we hope to gain the best crack results at the minimum drillhole numbers. This paper used RFPA software to set up some models with different drillhole numbers, gained different failure process of models. Adopted different drilling plan will occur different results. We should drill more holes if we need partly crack smoothly. We can plan the number of drillholes based on our need if we can use RFPA to simulate the failure process before beginning.

Abstract: The primary methods are antetype observation and model tests which to check the actual engineering status in geotechnical engineering field. The antetype observation is the best direct and convictive method, but approach miscellaneous and spend hugely. The general model tests can not fulfil the same stress between model and antetype. Geotechnical centrifuge model test can not only minish the measure of model and fulfil the comparability condition, but also can found all kinds of non-symmetrical models and simulation all kinds of complicated engineering. So the geotechnical centrifuge model test is applied widely in the geotechnical engineering. This paper used the RFPA-Centrifuge and recured to the principle of geotechnical centrifuge model test, evaluated the safety of model only by increase the physical strength. Though the numerical calculating in nonhomogeneous models with different scales showed that stress, displacement and failure mode were accord with conform ratio of centrifuge model tests. Showed the advantage that the results of RFPA can be validated each other with results of physical tests. For some specifical complicated items in geotechnical engineering, make a good test model is not only very hard and have to spend much time, but also need expensive test equipment and much money for test materials. It is very good if we can use a method to conquer these shortages. So it is advisable that using the mechod which geotechnical centrifuge tests combine RFPA-Centrifuge numerical simulation analysis method.

Abstract: Based on the microscopic damage mechanics, the finite element method is applied to investigate theinfluence of the inclined joint on the rock fragmentation under impact loading.The viscous boundary is considered to elimilate the influence of the reflected stress waves from the boundary. The result shows the inlcined joints change the direction of crack propagation. The lateral cracks appeare first, and thenthe main cracks tend to propagate to theleft side.

Abstract: Parallel fracture formation on surfaces of bi-layered columnar materials like growing tree trunk has been previously studied numerically. In this paper, numerical results of a continuous transition from parallel to polygonal fracture patterns with principal stress ratio provides the clear convincing theoretical explanation for fracture spacing. We perform three-dimensional simulations of fracture growth in a bi-layered columnar model with an embedded heterogeneous layer under inner radial expansion and terminal tension by finite element approach. As a result of this expansion, the bark stretches until it reaches its limit of deformation and cracks. A novel numerical code, 3D Realistic Failure Process Analysis code (abbreviated as RFPA3D) is used to obtain numerical solutions. In this numerical code, the heterogeneity of materials is taken into account by assigning different properties to the individual elements according to statistical distribution function. Elastic-brittle constitutive relation with residual strength for elements and a Mohr-Coulomb criterion with a tensile cut-off are adopted so that the elements may fail either in shear or in tension. The discontinuity feature of the initiated crack is automatically induced by using degraded stiffness approach when the tensile strain of the failed elements reaching a certain value. Numerical results of a continuous transition from parallel to polygonal fracture patterns with principal stress ratio are obtained by varying simulation parameters, the thickness of the material layer. We find that, except for further opening of existing fractures after they are well-developed (saturation), new fractures may also initiate and propagate along the interface between layers, which may serve as another mechanism to accommodate additional strain for fracture saturated layers.

Abstract: Fault is one of the most important factors affecting tunnel instability. As a significant and casual construction of Jinping II hydropower station, when the drain tunnel is excavated at depth of 1600 m, rockbursts and water inrush induced by several huge faults and zone of fracture have restricted the development of the whole construction. In this paper, a progressive failure progress numerical analysis code-RFPA (abbreviated from Rock Failure Process Analysis) is applied to investigate the influence of faults on tunnel instability and damaged zones. Numerical simulation is performed to analyze the stress distribution and wreck regions of the tunnel, and the results are consistent with the phenomena obtained from field observation. Moreover, the effects of fault characteristics and positions on the construction mechanical response are studied in details. Some distribution rules of surrounding rock stress of deep-buried tunnel are summarized to provide the reasonable references to TBM excavation and post-support of the drain tunnel, as well as the design and construction of similar engineering in future.

Abstract: Nnumerical tests on three-dimensional failure process of rock samples containing vertical wall semi-arched tunnel with and without reinforcing are carried out with Mechsoft’s RFPA-Parallel system running on Lenovo 1800 Cluster, reproducing zonal disintegration phenomenon within rockmass around deep tunnels, and then the deep tunnel reinforcing influences on zonal disintegration within rockmass around tunnel is analyzed. Numerical results indicate that deep tunnel reinforcing does not change the general nature to form zonal disintegration phenomenon, but it can improve the stability of the tunnel wall.

Abstract: This research applied a numerical code, RFPA2D (Realistic Failure Process Analysis) to evaluate the stability and investigate the failure mode of the high rock slope during excavations based on Strength Reduction Method (SRM). The corresponding shapes and positions of the potential slip surfaces are rationally simulated in different stages, and the related safety coefficients are obtained, which agrees well with the allowable minimum safety factors of the slope. The numerical results show that the safety coefficient drops from 1.25 at the natural state to 1.09 after excavation, and then increases to 1.35 after slope reinforcement. Moreover, the potential slip surface of the left bank moves into deep rock mass after taking support measures, which demonstrates the reinforcement is reasonable and efficient. The study shows that cracks and faults will cause crucial influences on the slope stability, and RFPA2D is a good tool to directly display the potential slip surface of the slope, which will offer valuable guidance for bolt support.

Abstract: Reflective crack is one of the major technical problems in highway with semi-rigid base, studying its formatting mechanism is of great significance. By means of a numerical analysis method named RFPA, formatting process of reflective crack such as initiation and expansion was studied in asphalt pavement with semi-rigid base. Two-dimensional model of asphalt pavement with cement-treated base was established based on mechanical parameters, thickness and homogeneity of commonly used structural layer in china, symmetrical and non-symmetrical load were both considered, and crack of cement-treated base was set before loaded. First, reasons for crack initiation were studied below the bottom layer subjected to different types of loads. The conclusion showed crack under symmetrical load mainly due to pull destruction while crack under non-symmetrical load mainly due to shear failure. Then, crack expansion in asphalt layer subjected to different load numbers with different homogeneity material was studied. The result showed that with the increase of the load numbers, the deformation in the same level deformation grows continuously. Different homogeneity level of layer material has an important influence on crack expansion; higher homogeneity has better regularity.

Abstract: Realistic Failure Process Analysis (RFPA3D) was used to simulate the concrete-filled rectangular steel tube columns which are subjected to axial loads. The ultimate bearing capacity and the load-strain figures were presented. The Numerical simulation results were verified by experimental data of the paper [5]. Meanwhile, the development process of crack in the specimen was described. The whole failure process of rectangular steel tube columns was reproduced. The failure principles of concrete-filled rectangular steel tube column were discussed deeply.

Abstract: Fracture formation on surfaces of bi-layered materials is studied numerically. A simplified two-layered materials model like growing tree trunk is present. This work is focused on patterns of fractures and fracture saturation. We consider the formation of crack pattern in bark as an example of pattern formation due to expansion of one material layer with respect to another. As a result of this expansion, the bark stretches until it reaches its limit of deformation and cracks. A novel numerical code, 3D Realistic Failure Process Analysis code (abbreviated as RFPA3D) is used to obtain numerical solutions. In this numerical code, the heterogeneity of materials is taken into account by assigning different properties to the individual elements according to statistical distribution function. Elastic-brittle constitutive relation with residual strength for elements and a Mohr-Coulomb criterion with a tensile cut-off are adopted so that the elements may fail either in shear or in tension. The discontinuity feature of the initiated crack is automatically induced by using degraded stiffness approach when the tensile strain of the failed elements reaching a certain value. The different patterns are obtained by varying simulation parameters, the thickness of the material layer. Numerical simulation clearly demonstrates that the stress state transition precludes further infilling of fractures and the fracture spacing reaches constant state,i.e. the socalled fracture saturation. It also indicates that RFPA code is a viable tool for modeling fracture formation and studying fracture patterns.