Papers by Keyword: Tool Durability

Abstract: In this work, the process of formation of a built-up edge during the cutting of hot metal rolls by rotary saws is considered. The study is conducted to increase the tool's durability.

Abstract: Essential factors of each new discovery or piece of knowledge in science are predetermined, prepared and realized experiment. Every successfully realized experiment with obtained outputs and measurements indicates the gauge of asset that has been achieved by its execution. After analyzing of outputs final dependencies can be described that generalize whole experiment and allow entire process to be analytically identified. The production of bearings is very difficult process. Especially production of bearing rings is very complicated. Optimization of this process means significant savings for the company. Bearing rings are produced by turning. One of the most important parts of the turning process is cutting tool. On the base of cutting tools are determined many factors for example: quality, price, cutting speed, etc. All these factors of cutting tools are the only consequence of these cutting tools durability. Cutting tool durability determines its cutting properties and machinable ability. Specification of tool wear by means of calculation is very difficult. Durability of cutting tools is defined in standard ISO 3685. In standard ISO 3685 is defined T-v_c dependence for different cutting materials and standard included process evaluation of tool durability for cutting materials made of high speed steel, sintered carbide and cutting ceramic. The article describes evaluation of T-v_c dependence on the selected type of cutting materials and theirs comparison with measured values T-vc dependence that are defined in standard ISO 3685.

Abstract: Cutting tool durability is very important cutting tool property. Especially for cutting ceramic is necessary to define durability dependence on available set of cutting speeds and to determine lifetime of tools made of cutting ceramic. Durability of cutting tools is defined in standard ISO 3685. In standard ISO 3685 is defined T-v_c dependence for different cutting materials and standard included process evaluation of tool durability for cutting materials made of high speed steel, sintered carbide and cutting ceramic. Specification cutting tools durability made of cutting ceramic in machining process of steel 100Cr6 is very important for economics of small and medium-sized enterprises, because cutting tool durability is factor that significantly affects the budget of these enterprises. This problematic is determined for small and medium-sized manufacturers of bearings, because steel 100Cr6 is most commonly used for production of bearing rings 100 mm in diameter. This material is usable for actuator (actuators and reduction gears) too. Description of cutting ceramic durability could mean for bearings manufacturer determination of optimal cutting parameter with maximum possible use of tool lifetime. Standard ISO 3685 contains instructions how to create T-v_c dependence for cutting tools made of cutting ceramic. In this standard are only instructions how to create T-v_c dependence according to Taylor. The article compares T-v_c dependencies for various cutting ceramics (Al₂O₃, Al₂O₃+ZrO₂, Al₂O₃+TiCN) with T-v_c dependence defined in standard ISO 3685, because this standard describes T-v_c dependence for all entered cutting materials together.

Abstract: Durability is very important property of every cutting material. This property of cutting materials defined theirs life-time. Technical science defines a lot of different factors, that they may be cause of shorter life-time of cutting tool. Maximally possible elimination of these factors is necessary for optimization of cutting materials life-time. Durability of cutting materials is defined in standard ISO 3685. The main part of standard ISO 3685 is T-vc dependence definition for selected cutting materials. One of these cuting materials contained in this standard is cutting ceramic. Standard ISO 3685 contains instructions how to create T-vc dependence for cutting tools made of cutting ceramic. In this standard are only instructions how to create T-vc dependence according to Taylor, but last part of every experiment is analytical expression of tested dependence. The article describes process how to define and analytically express T-vc dependence for cutting ceramic (Al2O3).

Abstract: In this paper, based on analyzing the properties of medical Ti-6Al-4V Titanium alloy, the author takes the purpose of studying the machinability of the medical Ti-6Al-4V Titanium alloy and aims at improving the tool durability. The study starts from the tool material, geometrical parameters of the tools, usage for the cutting and other aspects in order to achieve the suitability of selecting cutting tool as well as the optimization of choosing cutting usage which lays the foundation for further investigation of the machinability of the medical Ti-6Al-4V Titanium alloy and carry out the online optimization of cutting parameters.