Fabrication of Metal Matrix Ceramic Coating and its Erosive Wear Behaviour


Article Preview

By simulating the solid-gas duplex erosive wear condition, the fabricating process of the metal matrix ceramic coating was investigated, and the properties of the ceramic coating under different fabricating conditions were studied, and the erosive wear behaviour of the ceramic coating with different volume fraction of Al2O3 particles and the mechanisms of material removal were researched and discussed. The results show that the metal matrix ceramic coating should be fabricated on the enamel coating which was prepared in advance on Q235A steel surface, and the anti-wear property of the ceramic coating containing Al2O3 is better than the coating without Al2O3, and the coating with 40% volume fraction particles, eroded at velocity of 20 m/s at 45° impact angle, is the best, which is 3.67 times than that of the enamel coating.



Edited by:

Yiyi Zhouzhou and Qi Luo




X. B. Gu et al., "Fabrication of Metal Matrix Ceramic Coating and its Erosive Wear Behaviour", Applied Mechanics and Materials, Vol. 79, pp. 192-197, 2011

Online since:

July 2011




[1] J.F. Zhang, Z.F. zhou: Friction and anti-abrasion technology, Tianjin: Science and technology translation publishers Ltd., (1993).

[2] J.J. Liu: Material wear principle and abrasion resistance, Beijing: Tsinghua university press, (1993).

[3] B.S. Xu, S.H. Zhu: Surface engineering theory and technology, Beijing: National defence industry press, (1999).

[4] G. Dong, J.Y. Zhang: Solid particle erosion wear research progress, Journal of materials science and engineering, Vol. 21(2) (2003), p.307~312.

[5] J.E. Zhou, J.K. Li, W.H. Jiang: Metal matrix preparation of ceramic coating application and development, Journal of Ceramics, Vol. 259(3) (2004), p.179~184.

[6] Navinsek B, Panjan P: Oxidation of CrNx hard coatings reactively sputtered at low temperature, Surface and Coatings Technology, Vol. 179(4) (2004), p.215~222.

DOI: https://doi.org/10.1016/0040-6090(93)90718-5

[7] Gazala Ruhi, Modi O P, Singh I B, et al: Wear and electrochemical characterization of sol~gel alumina coating on chemically pre-treated mild steel substrate, Surface and Coatings Technology, Vol. 201 (2006), p.1866~1872.

DOI: https://doi.org/10.1016/j.surfcoat.2006.03.013

[8] A. J. Sparks and I. M. Hutchings: Transitions in the erosive wear behaviour of a glass ceramic Wear, Vol. 149 (1991), p.99~110.

DOI: https://doi.org/10.1016/0043-1648(91)90367-4

[9] A. Mohajerani, J.K. Spelt: Edge rounding of brittle materials by low velocity erosive wear, Wear, Vol. 267 (2009), p.1625~1633.

DOI: https://doi.org/10.1016/j.wear.2009.06.004

[10] Said Bouzid, Nourredine Bouaouadja: Effect of impact angle on glass surfaces eroded by sand blasting, Journal of the European Ceramic Society, Vol. 20 (2000), p.481~488.

DOI: https://doi.org/10.1016/s0955-2219(99)00140-5

[11] Y.F. Wang, Z.G. Yang: Finite element model of erosive wear on ductile and brittle materials, Wear, Vol. 265 (2008), p.871~878.

DOI: https://doi.org/10.1016/j.wear.2008.01.014

Fetching data from Crossref.
This may take some time to load.