Evaluation of the Cutting Force and Geometric Error for Roughing Operation by Plunge Milling

Abstract:

Article Preview

Nowadays there has been noticeable an expressive technological development in the cutting process to machine moulds and dies, through applying new materials, cutting tools and machining strategies. The rough operations depict an important portion in the machining time of these pieces. In front of this scenario, a new milling rough operation in the tool’s axial direction represents a possibility to optimize this machining process so as decreasing the machining time and increasing the material removes rates. A few scientific studies have been carrying out at this thematic, limited to a technical-commercial researches. Therefore this work contributes with the knowledge in this machining process through an experimental trial analyses. In special it studies the cut direction effects during climb and conventional milling in these operations. The result quantifies the cutting parameters influence at the cutting force and error form.

Info:

Periodical:

Edited by:

J.C. Outeiro

Pages:

350-358

Citation:

I. Bonetti et al., "Evaluation of the Cutting Force and Geometric Error for Roughing Operation by Plunge Milling", Advanced Materials Research, Vol. 223, pp. 350-358, 2011

Online since:

April 2011

Export:

Price:

$38.00

[1] I. Lazoglu, Y. Altintas: Prediction of tool and chip temperature in continuous and interrupted machining, volume 42 of Journal of Machine Tools & Manufacture, (2002).

DOI: https://doi.org/10.1016/s0890-6955(02)00039-1

[2] C.K. Toh: Static and dynamic cutting force analysis when high speed rough milling hardened steel, volume 24 of Journal of Materials and Design (2003).

DOI: https://doi.org/10.1016/s0261-3069(03)00160-2

[3] R.L. Capla, in: Estudo da Influência do Sobremetal Excedente de Desbaste na Operação de Acabamento Aplicando Usinagem com Altas Velocidades, Department of Mechanical Engineering São Carlos, Brazil (2006).

DOI: https://doi.org/10.11606/d.18.2006.tde-13022007-172927

[4] A.F. Souza, in: 2004, Contribuições ao Fresamento de Geometrias Complexas Aplicando a Tecnologia de Usinagem com Altas Velocidades, Department of Mechanical Engineering, São Carlos, SP, Brazil (2004).

DOI: https://doi.org/10.11606/t.18.2004.tde-14012005-101635

[5] A.F. Souza, I. Bonetti, in: Contato Ferramenta-Peça no Fresamento de Formas Geométricas Complexas, edtied by Aranda Editora Técnica e Cultural, São Paulo, Brazil (2008), in press.

[6] M. Al-Ahmad, A. D'Acunto: Prediction of Cutting Forces System in Plunge Milling Operations in the Case of Full Radial Engagement of the Cutter, submitted to Sixth International Conference High Speed Cutting (2007).

[7] J.Y. Hascoet, M. Rauch, S.H. Suh: Relevance of Step-NC Standard for High Leve Toolpaths generation, submitted to Sixth International Conference High Speed Cutting (2007).

[8] S. Wakaoka, Y. Yamane, K. Sekiya, N. Narutaki: High Speed and High Accuracy Plunge Cutting for Vertical Walls, volume 127 of Journal of Materials Processing Technology (2002).

DOI: https://doi.org/10.1016/s0924-0136(02)00151-6

[9] J.H. Ko, Y. Altintas: Time Domain Model of Plunge Milling Operation, volume 47 of Journal of Machine Tools and Manufacture (2006).

DOI: https://doi.org/10.1016/j.ijmachtools.2006.08.007

[10] Y.N. Hu, W.C. Tse, Y.H. Chen, Z.D. Zhou: Tool-path planning for rough machining of a cavity by layer-shape analysis, volume 14 of Journal Advance Manufacturing Technology (1998).

[11] A.E. Diniz, F.C. Marcondes, N.L. Coppini, Tecnologia da Usinagem dos Materiais, edtied by MM Editora, São Paulo, Brazil (2006).

[12] K.A. Abou-El-Hossein, K. Kadirgama, M. Hamdi, K.Y. Benyounis: Prediction of Cutting Force in End Milling Operation of Modified AISI P20 Tool Steel, volume 182 of Journal of Materials Processing Technology (2007).

DOI: https://doi.org/10.1016/j.jmatprotec.2006.07.037

Fetching data from Crossref.
This may take some time to load.