Research on Finite Element Simulation and Test of Two-Pass Deep Drawing Forming for Conical Parts


Article Preview

This paper is focus on two-Pass Deep Drawing Forming of conical axisymmetric parts, study on the finite element simulation and test of multi-Pass deep drawing part. It carry on the finite element analysis and calculation using the ANSYS/LS-DYNA software platform, analyzing the simulation results such as stress , strain distribution and formability by post-processing LSPOST software. It was done multi-Pass deep drawing test using a set of combined type mould. Based on the multi-Pass forming test by using a set of combined type mould, comparison of simulation and test data can be obtained through the forming limit diagram. The result of simulation and test is basically the same and both reflect the formability.



Advanced Materials Research (Volumes 652-654)

Edited by:

Zhengyi Jiang, Xianghua Liu, Sihai Jiao and Jingtao Han




Z. R. Han and Z. B. Yuan, "Research on Finite Element Simulation and Test of Two-Pass Deep Drawing Forming for Conical Parts", Advanced Materials Research, Vols. 652-654, pp. 1966-1970, 2013

Online since:

January 2013




[1] Feng, Ruan; Langui, Xu; Bo, Wang . Study on key problems in multi-stage deep drawing numerical simulation of ultra-thin sheet[J]. Proceedings - 2009 International Conference on Computer Modeling and Simulation, 2009, 310-312.


[2] Stoughton T B; Zhu Xinhai . Review of theoretical models of the strain-based FLD and their relevance to the stress-based FLSD, 2004, 8-9.


[3] Bressan, José Divo; Cieto, José Carlos; Vieira, Fabio Henrique. A numerical simulation study of deep drawing testing and experimental results of steel sheets, using a comercial software [J]. International Journal of Material Forming, 2010, 4, 231-234.


[4] Morovvati, M.R.; Mollaei-Dariani, B.; Asadian-Ardakani, M.H. A theoretical, numerical, and experimental investigation of plastic wrinkling of circular two-layer sheet metal in the deep drawing[J]. Journal of Materials Processing Technology, 2010, 10, 1738-1747.


[5] Barata da Rocha, A.; Santos, Abel D.; Teixeira, Pedro. Analysis of plastic flow localization under strain paths changes and its coupling with finite element simulation in sheet metal forming[J]. Journal of Materials Processing Technology, 2009, 6, 5097-5109.


[6] Savas V, S ecg in O. A new type of deep draw ing d ie design and experim en tal resu lts [J] . Ma terials& Design, 2007, 28.

[7] Park C S, et al. P rocess design and blankm od ification in them u-lt istage rectangu lar deep draw ing of an extrem e aspect ratio [J]. Ma terials P rocessing Technology, 2004, 153~ 154: 778 ~ 784.

[8] Ying Huang, Yi-Ping Chen, Ruxu Du. A new approach to solve key issues in multi-step inverse finite-element method in sheet metal stamping[J]. International Journal of Mechanical Sciences, 2006: 591-600.


[9] K. Moir,Y. Abe,O. ebihara. Prevention of shock lines in multi-stage sheet metal forming[J]. International Journal of Machine Tools & Manufacture, 2003, (43): 1279-1285.


[10] Jianhua Yang, Wei Pan, Dannong He, Yinghong Peng. Research on forming laws and deformability in multi-stage sheet metal drawing. Forging & Stamping Technology, 2002(5): 22-24.

[11] Hongzhi Tao, Dannong He. Key Technologies of Finite Element Modeling in Multi-stage Deep Drawing Process. DIE AND MOULD TECHNOLOGY, 1999(5): 20-23.

[12] Yan Chen, Lin Gao, Xianzhi Wu. Research on Multistage Deep Drawing and Ironing of an Irregular Cup. Mechanical Science and Technology for Aerospace Engineering, (2009).

[13] Linjun Yang, Xinan Dang, Wei ren. Research on the Optimization of Technological Parameters of Sheet Metal Drawing by Orthogonal Experiment. Manufacturing Technology & Machine Tool, (2006).