The Influence of 0.1% Sc Addition on the Microstructure and Texture Development in Al-Zn-Mg-Cu-Zr Alloys

Abstract:

Article Preview

In this study, the microstructure and the texture development in Al–Zn–Mg–Cu–Zr alloys with/without 0.1%Sc has been investigated after extrusion, cold rolling, and aging treatment. After aging treatment, in Al alloy without Sc recrystallized equiaxed grains are obtained, while in Al alloy with Sc fine grains with an average size of 0.1~0.3 μm are obtained. After cold rolling, in case of the sample from the cross section (CS) to which Sc was added, texture with {112}<111>(Cu) + weak {123}<634>(S) component was developed while in case of the sample from longitudinal section (LS) to which Sc was added, texture with strong β-fiber + {110}<001>(Goss) components was developed. In case of CS and LS without Sc, texture of β-fiber was developed. After solid solution treatment and aging treatment, Al alloys (LS and CS) with Sc had rolling texture while Al alloys without Sc had random texture. The role of these differently developed textures in the plastic behavior, such as the normal anisotropy r-value (the plastic strain ratio) and planar anisotropy r-values are discussed.

Info:

Periodical:

Materials Science Forum (Volumes 539-543)

Main Theme:

Edited by:

T. Chandra, K. Tsuzaki, M. Militzer , C. Ravindran

Pages:

463-468

Citation:

D. S. Chung et al., "The Influence of 0.1% Sc Addition on the Microstructure and Texture Development in Al-Zn-Mg-Cu-Zr Alloys", Materials Science Forum, Vols. 539-543, pp. 463-468, 2007

Online since:

March 2007

Export:

Price:

$38.00

[1] M. Nakayama, A. Furuta and Y. Miura: Mater. Trans. JIM. Vol. 38 (1997) 852.

[2] J. S. Vetrano, S. M. Bruemmer, L. M. Pawlowski and I. M. Robertson: Mater. Sci. Eng. A Vol. 238 (1997) 101.

[3] T. G. Nieh, R. Kaibyshev, L. M. Hsiung, N. Nguyen and J. Wadsworth: Scripta mater. Vol. 36 (1997) 1011.

[4] T. G. Nieh, L. M. Hsiung, J. Wadsworth and R. Kaibyshev: Acta mater. Vol. 46 (1998) 2789.

[5] R. Sawtell and C. L. Jensen: Metall. Trans. A Vol. 21 (1990) 421.

[6] Y. A. Filator, V. I. Yelagin and V. V. Zakharov: Mater. Sci. Eng. A Vol. 280 (2000) 97.

[7] S. Lee, A. Utsunomiya, H. Akamatsu, K. Neishi, M. Furukawa, Z. Horita and T. G. Langdon: Acta mater. Vol. 50 (2002) 553.

[8] V. Ocenasek and M. Slamova: Mater. Character. Vol. 47 (2001) 157.

[9] G. M. Novotny and A. J. Ardell: Mater. Sci. Eng. A Vol. 318 (2001) 144.

[10] E. A. Marquis and D. N. Seidman: Acta mater. Vol. 49 (2001) (1909).

[11] K. B. Hyde, A. F. Norman and P. B. Prangnell: Acta mater. Vol. 49 (2001) 1327.

[12] S. Komura, P. B. Berbon, M. Furukawa, Z. Horita, M. Nemoto and T. G. Langdon: Scripta mater. Vol. 38 (1998) 1851.

DOI: https://doi.org/10.1016/s1359-6462(98)00099-2

[13] H. J. Bunge: Texture Analysis in Materials Science, Butterworths Pub., London (1982).

[14] C. J. Jae, S. J. Jin, D. S. Chung, S. T. Lim, Y. Y. Lee and N. J. Park: J. Kor. Inst. Met. Mater. Vol. 42 (2004) 797.

[15] N. J. Park, S. J. Jin, C. J. Jae, S. T. Lim, Y. Y. Lee and D. S. Chung: Solid State Phenomena Vol. 105 (2005) 213.

Fetching data from Crossref.
This may take some time to load.