Technological Improvement of Surfacing of Parts of Hammer Crushers Used in Coke-Chemical Industry

Abstract:

Article Preview

A technology of manufacturing surfacing with high-chromium special cast iron without heating is developed; the main directions for improving surfacing quality are outlined. It is proposed to replace manual arc welding with plasma surfacing using high-speed hard surfacing materials.

Info:

Periodical:

Edited by:

Dr. Dmitry A. Chinakhov

Pages:

168-175

Citation:

N.N. Malushin et al., "Technological Improvement of Surfacing of Parts of Hammer Crushers Used in Coke-Chemical Industry", Materials Science Forum, Vol. 927, pp. 168-175, 2018

Online since:

July 2018

Export:

Price:

$38.00

[1] Paton B.E. Welding problems at the turn of the century, J. Welder. 1 (1999) 2-3.

[2] Gueller Yu.A. Tool steels. Metallurgy, (1975) 584.

[3] Frumin I I Automated electric arc welding Metallurgizdat (1961) 421.

[4] Gusev A.I., Kozyrev N.A., Osetkovskiy I.V., Kozyreva O.A., Valuev D.V. Quality of metal deposited flux cored wire with the system Fe-C-Si-Mn-Cr-Mo-Ni-V-Co, J. Key Engineering Materials. 736 (2017) 23-28.

[5] Silkin A.A., Linnik A.A., Pankratov A.S.,. Kurganova Yu. A, Kobernik N.V., Mikheev R.S. Formation of the Structure of the Weld Metal upon the Introduction of Nanoparticles into the Weld, J. Russian Metallurgy (Metally). 13 (2016) 1253 – 1256.

[6] Petrushin S.I., Gubaydulina R.K., Grubiy S.V., Likholat A.V. On the Problem of Wear Resistant Coatings Separation From Tools and Machine Elements, J. IOP Conference Series: Materials Science and Engineering. 91 (2015).

[7] Fedorov N.S. Zubkov N.S. Krepysheva L.B. Thermal treatment effects upon hardness and phase composition of the hard-faced high-speed steels J Newsletter of Higher Educational institutions. Ferrous metallurgy 8 (1983) 59–63.

[8] Paton B.E. Technology of electric welding of metals and alloys by fusion Mashinostroyeniye (1974).

[9] R.Q. Puchola, J.R. Blancoa, L.P. Gonzaleza, G.C. Hernandeza, R. G. Pereza, The influence of the air occluded in the deposition layer of flux during automatic welding: a technological aspect to consider in the quality of the bead, J. Welding International. 23 (2009).

[10] Kadukov V.G. Kogan A E Fomin N A Stirring intensity effect upon the duration of blowing J Izv. Vuzov 6 (1986) 46 – 57.

[11] Vostretsova T.G. Regulated thermal cycle for plasma-jet hard-facing of rollers with heat-resistant steels, J. Zagotovitelnye proizvodstva v machinostroyenii 13 (2014) 14–17.

[12] N.N. Voronin, Technology of aluminothermic welding of rails. Moscow: MIIT, (2008) 117 p.

[13] F. Mitsuru, Rail flash-butt welding technology, J. JFE Technical Report. 20 (2015) 159 – 163.

[14] K. Saita, K. Karimine, M. Ueda, K. Iwano, T. Yamamoto, K. Hiroguchi, J. Nippon steel & sumitomo metal technical report. 105 (2013) 84 – 92.

Fetching data from Crossref.
This may take some time to load.