Characterisation of Precipitation and Coarsening of Carbides during Tempering in a Low Alloyed Quenched and Tempered Steel


Article Preview

Low alloy quench and tempered (Q&T) steels plates up to 100mm thick are used in applications such as cranes and earth movers due to their combination of high strength and toughness. In order to ensure that appropriate tempering conditions are used to give optimum properties through thickness in Q&T steels it is desirable to be able to predict the effect of composition and tempering conditions (time and temperatures) on the microstructure and hence the hardness evolution. In this paper, the types and coarsening rates of carbides formed in a low alloyed Q&T steel have been investigated on tempering at 600 °C. It has been found that in the as-quenched condition auto-tempered martensite is present with needle-shaped epsilon and cementite particles, whilst after different tempering times (1 - 16 hours) cementite becomes the stable phase with an elliptical shape, which coarsens with time. Besides, the coarsening of inter-lath cementite with a faster rate is independent from that of intra-lath ones.



Main Theme:

Edited by:

R. Shabadi, Mihail Ionescu, M. Jeandin, C. Richard and Tara Chandra




Y. L. Ju et al., "Characterisation of Precipitation and Coarsening of Carbides during Tempering in a Low Alloyed Quenched and Tempered Steel", Materials Science Forum, Vol. 941, pp. 33-38, 2018

Online since:

December 2018




* - Corresponding Author

[1] E. R. Parker and R. E. Mehl. Interrelations of compositions, transformation kinetics, morphology, and mechanical properties of alloy steels. Metall. Mater. Trans. A, 8A (1977) 1025-1042.


[2] S. W. Ooi, Y. R. Cho, J. K. Oh and H. K. D. H. Bhadeshia. Carbon enrichment in residual austenite during martensite transformation. Proceedings of International Conference on Martensite Transformation, (2009) 179-185.

[3] H. K. D. H. Bhadeshia and R. W. N. Honeycombe. Steels: Microstructure and properties, third ed., Elsevier Ltd, Cambridge, (2006).

[4] R. Thomson and M. Miller. The partitioning of substitutional solute elements during the tempering of martensite in Cr and Mo containing steels. Applied Surface Science, 87 (1995) 185-193.


[5] G. Miyamoto, J. C. Oh, K. Hono, T. Furuhara, T. Maki. Effect of partitioning of Mn and Si on the growth kinetics of cementite in tempered Fe–0.6 mass% C martensite. Acta Materialia, 55 (2007) 5027-5038.


[6] S. Ghosh. Rate-controlling parameters in the coarsening kinetics of cementite in Fe–0.6 C steels during tempering. Scripta Materialia, 63 (2010) 273-276.


[7] W. Steven and A. G. Haynes. The temperature formation of martensite and bainite in low-alloy steels, some effects of chemical composition. The Journal of the Iron and Steel Institute, 183 (1956) 349-359.

[8] J. M.R Génin. On the morphology of the modulated precipitation of extended multiplets and Fe9C4 epsilon or eta carbide obtained by aging and tempering in Fe-C martensite. Metallurgical and Materials Transactions A, 19 (1988) 2901-2909.


[9] G.E. Totten. Steel heat treatment: Metallurgy and technologies. Taylor & Francis Group, Oregon, USA, 2007, p.108.

[10] C. A. Wert. Diffusion coefficient of C in α-Iron. Physical Review, 79 (1950), 601-605.

[11] H. Bhadeshia, S. David, J. Vitek, et al. Stress induced transformation to bainite in Fe–Cr–Mo–C pressure vessel steel. Materials Science and Technology, 7 (1991) 686-698.


[12] National Bureau of standards. X-ray Powder Data File (cric 539 4 3). card for alpha-iron. U.S. Department of commerce.(1955).

[13] S. T. Ahn, D.S. Kim and W. J. Nam. Microstructural evolution and mechanical properties of low alloy steel tempered by induction heating. Journal of Materials Processing Technology, 160 (2005) 54-58.


[14] G. Greenwood. The growth of dispersed precipitates in solutions. Acta Metallurgica, 4 (1956) 243-248.


[15] S. Yamasaki. Modelling Precipitation of Carbides in Martensite Steels. PhD thesis, University of Cambridge. (2004).