Search results

For example, platinum/poly(4-methyl-1-pentene) (PMP) composites [4] have been obtained by impregnation and reduction of CODPtMe2 in presence or not of CO2 and H2.
For a comparison with literature data, CO2 mass sorption incorporated into polymer matrix is given by Eq. 5 where ρpol is the polymer density.
We have confirmed the reduction of PEG viscosity under scCO2 conditions.

For pure mode II where B is about 1.6 a reduction in mode II fracture toughness is expected to take place.
A similar reduction in mode II fracture toughness due to positive T-stress has been observed in experimental results obtained from fracture test on the semicircular bend specimen [11].
Aliha: (2006) "Wide Range Data for Crack Tip Parameters in Two Disc-Type Specimens under Mixed Mode Loading" Computl.

The CO with high energy desorbs easily from the surface of the catalyst leading to the reduction of the poisonous effect of the CO to the HT-PEM fuel cell.
The electrochemical reaction site for the reduction reaction of the hydrogen sharply decreases.
(a) (b) Fig.5 The effects of CO on the AC impedance in the HT-PEM fuel cell 　The data of the AC impedance of the HT-PEM fuel cell obtained by the experiments is analyzed based on the equivalent circuit method.

To this end, it is need to do a series of steps as binary processing, noise reduction, remove frame [2].
When faced with the need for connectivity up fork merge field, with the design of data structures in this article connectivity components of the merger.
Practice has proved that the above connected component generation, noise reduction, to the border and the word segmentation algorithm effective.

The reduction of Ms should be attributed to the reduced volume fraction of Co atoms in the film.
This should be attributed to the simultaneous reduction of Ku and Ms which resulted in a stable anisotropy field.
Lim Boon Chow from the Data Storage Institute in Singapore.

AlN can be synthesized by a variety of processing methods including carbothermal reduction of Al2O3, direct nitridation of Al, chemical vapor deposition (CVD), polymer pyrolysis, and arc plasma [2].
Among them, two synthesis processes are currently used for commercial production of AlN powders: One is the carbothermal reduction method, and the other is the direct nitridation method.
Combustion temperature and velocity were measured with a W/Re thermocouple connected with a data collecting system.

The temperature dependencies exhibit characteristic behaviors depending on the current flow direction and the number of high-temperature annealing rounds　(the abrupt jump around 100K in the data for the resistivity parallel to the basal plane after the 3rd annealing is an artifact).
The mechanism of the observed reduction of the SF density is yet to be clarified.
The measured SF densities in the crystals, where the reduction of SF density was observed after annealing, were well correlated with the resistivity changes.

Numerous precious data on surface integrity, including surface roughness, microhardness, plastic deformation and residual stress when machining Inconel 718 have been published.
According to Ezugwu et al. [3], increasing the cutting speed also attributed to the reduction of the friction coefficients, which resulted in low friction at the tool-workpiece interface.
This enables the reduction of friction and heat between the tool-workpiece interface [5].

The tolerance allocation is determined also using the cost versus tolerance data available using optimization techniques [3, 4], considering the demands of manufacturing cost and product quality [5] are developed approaches based on the Shapley Value Method (SVM) of coalitional game theory but equally in [6] it is presented a tolerance allocation approach based on a tolerance allocation strategy that uses time as the basis for optimization, strategy suitable for use in a Concurrent Engineering (CE) framework.
Inverse of this ratio is the coefficient for proportional reduction P of components tolerance, anterior finding (row 34).
This entire tolerance ratio was multiplied with coefficient for proportional reduction P (row 37).

Introduction Starch-cadmium iodide methods used for oilfield sewage of polyacrylamide (HPAM) mass concentration analysis by SCOGGINS M W et al [1]for the first time，research indicates that adjustment buffer pH to 3.5 can eliminate interference a great quantity of Cl- in the sampe，in the buffer to add too much Al3+ can eliminate interference from Fe3+ and Bi3+ etc high cation．Junming Hu et al[2]choose the stable performance good soluble starch，iodine starch complex have the strongest absorption in the 590 nm place．The results showed that pH is between 3.7 and 4.5 absorbance changes smaller buffer pH adjustment to 4.0 advisable．Shiguang Yang et al[3]with NH4HF4-FeSO4 system instead of sodium formate also concentrate，measuring absorbance in the 420nm place，the method of measuring range from 0~6 mg/L expanded to 0~24 mg/L，and eliminate the absorbance with reduction reaction time increased and falling phenomenon。
Table2 The relationship between bromine water quantity and absorbance bromine water quantity/mL ρ(HPAM) ∕ (mg/L) 10 20 30 40 50 2 0.106 0.187 0.295 0.396 0.479 3 0.111 0.185 0.290 0.393 0.469 2.1.6 The dosage of sodium formate to the influence of the reaction system The experimental process found to join 5ml sodium formate after solution color not change, measuring its absorbance to zero, so that the 5ml sodium formate enough to make too much bromine reduction。
Then known by test data that ρ(HPAM)4.5 mg/L，5.0 mg/L，100.0 mg/L in the curve，and ρ(HPAM)4.0 mg/L ot of the curve．Starch-cadmium iodide method measuring the quality of HPAM concentration lower limie is 4.5mg/L and upper limit is 100.0 mg/L。