Search results

On the basis of the hot compression data, critical stress (strain) or peak stress (strain) were determined with the assistance of the strain hardening rate versus stress curves.
The reduction in height is 60% at the end of the compression tests.
DRX volume fraction X is often calculated in terms of the data from the strain-stress curves and can be expressed as [10]: (3) where sp is the peak stress, ss is the steady state stress and s is the specific stress from flow curves.
(3) The kinetics models were developed to describe the evolution of DRX based on the stress–strain data, and the typical model at 923 K and 0.1 s-1 was expressed as (e < ec) (e ≥ ec) Acknowledgments The present work was supported by Ministry of Education of Guangdong Province University-industry Cooperation Project (No.2012B091100038), University-industry Cooperation Project of Guangzhou (No.7411447290986) and the PhD start-up fund of Guangzhou Research Institute of Non-ferrous Metals (No.2012B001).

The system was demonstrated with real-world outdoor data.
Furthermore, we demonstrated our new observation model on real-world data.
M. in: Using laser range data for 3D SLAM in outdoor environments.
IEEE/RSJ International Conference on , vol., no., pp.1606,1611, 22-26(2008) [7] Sibley, G, Matthies L., Sukhatme G. in: Bias Reduction and Filter Convergence for Long Range Stereo.

The enhancement effect of pile-base post-grouting was analyzed through the comparison static loading tests and summarization of literature data.
Fig. 1 shows the discreteness of pile test data, reflects the control level of the bored pile construction technology.
Whereas, the load- displacement gradient data of pile-base post grouting piles is more discrete.
The shaft resistance reduction effect caused by the upward of pile, and the delay of the enhancement effect of tip resistance have led to the phenomenon that the stiffness of pile-base post-grouting pile below the general bored pile at the low load level.

In respond to the national energy saving, emission reduction, and development and utilization of new energy, and with the objective of practical application, a set of solar energy automatic bird expeller device is designed with solar photovoltaic technology, singlechip technology, and digital voice technology.
It is widely used in satellite communications systems, rural telephone, fiber optic, microwave transmission, two-way radio communication and data collection, radio electronic devices and LED lighting devices.
With solar lighting system charging and discharging efficiency sets at 0.75, solar battery module group loss correction coefficient sets at 0.95, dust shelter and other loss correction coefficient sets at 0.90, and via query data, unit conversion, and simplification processing, the calculation formula of total consumption P of solar battery is obtained as below [3]: P=5618×A×QL /（Kop×HL） (1) In the above formula, QL is load daily consumption (Wh); HL is horizontal face annual daily radiation capacity (KJ / (m2 • d)); Kop is slope face radiation best radiation coefficient; A is safety factor, generally sets at 1.1 to 1.3. 2) Selection of Storage Battery Common lead-acid battery has disadvantages of leakage fluid, corrosion, pollution, small discharge, ease explosion.

However, the great reduction of crafting window brings challenges to the soldering quality and also poses higher requirement for the stability and reliability of lead-free soldering equipment.
A variety of performance boost testing methods need researching and exploring together with data accumulating in order to shorten the setup time from exploring to producing[1].
According to the statistic data, there are more than 100 kinds of lead-free solders manufactured all over the world like solder paste, solder wire, welding stick, etc.

At that the main objectives of the research were reduction of the labor coefficient of work relating to the preparation of surfaces of metal building structures, by applying the rust painting method, and creation of anticorrosive materials with universal properties combining the functions of rust, primer and basic coating modifiers.
Analysis of the data in table 2, allows to draw the following conclusions: • coatings with compounds AKS-K and AKS-B protect the clean steel surface to the same extent as the standard coating systems.
The analysis of the graphical display of the data obtained gives interesting conclusions, if we take into account the criteria of the quality of coatings proposed by M.

A new modular design (MD) has been applied to test method for proportional relief valve characteristics, which realized the real-time data acquisition for multi-path pressure signal of automatic measurement & control and hydraulic system for steady state and dynamic state of DBE series proportional relief valve, and conducted analysis such as time domain, frequency domain, visualization and so on to collected data, obtained rather valuable test data and characteristics conclusion.
With good compatibility with virtual instrument LabVIEW software and rather high cost performance, it can effectively improve the whole performance of data acquisition system.
Carry out data acquisition and time-domain & frequency-domain analysis by means of LabVIEW and MATLAB.
Through design improvement and modular processing to the existing proportional relief valve test experiment, this system combines virtual instrument computer-aided test technology with MATLAB software, realizes real-time acquisition to two-channel and four-channel pressure signal and conducts time domain, frequency domain and visualization as well as other analysis to collected data.
Experiments show that, the proportional relief valve characteristic platform has reasonable structural design, compact size, stable performance and good cost performance; the test analysis system is efficient and convenient, the data analysis is reliable, and the test precision reaches the industrial measurement standard, all these lay good foundation for subsequent proportional valve pressure, flow-rate, displacement comprehensive test as well as multipoint real-time synchronous data acquisition.

As a general rule, data accuracy is reduced with increased punch speed.
In general, they require as input sheet thickness and material data.
Punch-Load data.
Press data and experimental conditions are summarized in Table 3.
As it can be seen, experimental data are affected by some noise.

According to the element analysis data, the least soluble fraction had the highest molybdenum content (Table 1).
Based on the element analysis data, the relative molecular weight of the elementary unit of this fraction was calculated.
The respective data are shown in Table 2.
This fragment size was calculated from the data of X-ray structural analysis of molybdenyl bis(acetylacetonate) [9].
As seen from the element analysis data, the compositions of these fractions did not virtually change after purification (Table 4).

Fig 1．Kawasaki annual amount of waste and population comparison chart[3] Solid waste management features of Kawasaki city Information disclosure and social supervision Through the computer network, data monitoring waste management is opened.
Based on this, in April 2009, the Beijing municipal government issued "n promoting the views of living garbage disposal work completel".Then Beijing city proposed by organizational security and management by objectives, at the same time accelerate the construction of waste incineration plant, comprehensive treatment plants and food waste treatment facilities, sub-for the year to achieve "increased capacity, adjusting structure, promoting reduction" goal.
Fig 2．Beijing annual amount of waste and population comparison chart[4] Innovation of household waste management in Beijing city Solid waste management innovation of the current Beijing city should include the following aspects: First, strengthen the data and information management, realize the whole process management in the classification of garbage collection, transportation, recycling, disposal data control With the rapid development of modern city informationization level and modernization of the administrative means,it has become very urgent to management informatization of municipal household waste.
The information of MIS(Management Information System) should include all relevant information from waste, collection, storage, processing, transport, intermediate processing treatment and utilization to the final disposal, include information related laws ,regulations and policy of national waste disposal,and include garbage disposal technology information.Among them ,the basic data collection is necessary for effective management of waste,so it is necessory to pay attention to the basic data collection, analysis, forecast and decision-making.
[5] Shenyang environmental protection bureau of China.http://www.syepb.gov.cn/data/2002_12_11/20021211122723.html.2014-4-3