Search results

The load data is shown in Table2.
The data measured are shown in Table 3.The120mm embedded wall panel is widely used in the practical engineering.
Its cracks is shown in Fig.4, the unit of data is KN in Fig.4.
The test data shows that the Magnesium lightweight wallboard is suit for the exterior wall of high-rise building and the applicable height is relate to the wallboard thickness and the connection mode.
Autoclaved aerated concrete produced with low noburner/selective catalytic reduction fly ash[J].Journal of Energy Engineering,2001(8):37-50

However, this very intuitive and simple approach often fails due to many problems, such as invalid areas and inconsistent data in the wrapped phase map, undersampling of fringe patterns, and unavoidable noise.
Examples show that it can deal with invalid data as well.
It verifies the effectiveness of the proposed filtering scheme in noise reduction.
The effectiveness of the propose approach in removing the noise and localizing the influence of invalid data is verified by real and simulated examples.
Measurement of elastic moduli using spherical indentation and digital speckle pattern interferometry with automated data processing [J].

LabVIEW is a graphical language suitable for data acquisition and information control, its program structure is data stream, which decides the operation sequence of procedure.
Hardware frame of the experiment system The hardware of vibration measurement and fault diagnosis system is a programmable data acquisition system, which includes vibration tester, sensors, signal conditioning instrument, DAQ card and computer, as shown in Fig. 1.
For obtaining exact characteristic parameters for fault diagnosis, data pretreatment methods and feature extraction methods can be combined arbitrarily according to the need.
For example, combining correlation analysis with demodulation analysis, the time delay correlation demodulation method can be got, which has a good effect on noise reduction and demodulation.
In the process of acquiring and processing experimental data, students can apply relevant theory into the practice of measurement and diagnosis and grasp the relevant knowledge.

(6) In formula (11), it proposes a feature reduction method based on class conditional distribution by using deviation classification of Bayesian algorithm [12].
Table.1 The combined effect index of words weight factors and the weight factors between classes on performance(C=256) ham% (%) spam% (%) Accuracy (%) 1:5 1:3 1.890(1.84-1.94) 0.515(0.59-0.44) 99.135(99.09-99.18) 1:5 1:5 1.940(1.77-2.11) 0.650(0.70-0.60) 99.015(99.02-99.01) 1:3 1:3 2.070(1.98-2.16) 0.440(0.49-0.39) 99.140(99.13-99.15) 1:3 1:5 2.280(2.01-2.55) 0.66(0.73-0.59) 98.925(98.94-98.91) 1:5 1:1 2.420(2.38-2.46) 0.315(0.33-0.3) 99.150(99.15-99.15) As the data shown in Table 1, for the construction of discourse system based on the improved Bayesian algorithm, the feature extraction and feature values calculation of the model is as shown in Figure 3.
Summary According to the increased uniform distribution of data distribution entropy, simulation and analysis data results of academic discourse system for Chinese characteristics news communication showed that, the analysis of naive Bayesian performance effect, and the data from simple bias to low entropy distributions could get better precision, so if it got rid of these data distribution characteristics which increased entropy, it could improve the classification performance of naive Bayesian, which would play an important role in construction of academic discourse system for Chinese characteristics news communication.

Table I shows the Dit data collected at 0.1 eV below the 4H-SiC conduction band, which decrease with increasing the NO annealing duration with a saturation at about 4×1011 cm-2eV-1.
The relevant data reported in Fig.4 are also summarized in Table I.
Fig.4: NTrap values (calculated from data shown in Fig.3) obtained on the MOSFETs subjected to PDAs in NO of different duration.
Table I: Survey of the electrical data collected on the investigated MOSFETs.
By a cross-comparison of all the electrical data summarized in Table I, it is possible to conclude that prolonged NO PDAs may induce detrimental effects.

Data In the Cloud, June 2008
[8] Gartner: Adaptations of Data Management Technologies and Providers[R].
Data In the Cloud, October 2009
Data In the Cloud, April 2009
Data In the Cloud, September 2009.

Study Area and Data Source A.
Data source The analytical data of landslide disasters included Landsat ETM+ remote sensing image mainly used for land vegetation classification research.
The image were provided for obtaining information about vegetation coverage using the combination of 6 wave bands of ETM+ such as NDVI. 1:50000 geographical data included basic geographic data viz. altimetric point, contour line and drainage system, DEM, gradient and aspect generated from 5m gap contour line; the engineering geological map mainly included data such as: stratigraphic distribution data, faults distribution data, pucker and attitude of stratum, etc. the disaster data is obtained from Quickbird image and field investigation.
It can be represented by: （1） Where, refers to the conditional probability of the occurrence of incidents (probability of landslide disaster) in the data class a.
By the support of GIS, ETM+ remote sensing data was utilized to extract vegetation index.

As a result of the experimental study of the process of draft of inhomogeneous material in a closed matrix, the data characterizing the pore formation and distribution of forces depending on the friction factor, the deformation rate and the degree of deformation are obtained.
The obtained experimental data can be used to construct a model describing the deformation of an inhomogeneous medium taking into account the compressibility of the material.
Similar data were obtained for the rest of the considered pores.
The data presented, together with the data table. 2 characterize the shaping of pores in the process of deformation.
The obtained experimental data can be used to construct a model describing the deformation of an inhomogeneous medium taking into account the compressibility of the material.

There are many measures of the energy consumption reduction.
The work in the paper used the experimental method to verify the effectiveness of the resistance reduction and energy saving[2].
Through the related datum, according to the hull lines of parent ship, this paper designed the model of SSD[4].
When the speed was 14.5kn, the open angle of profile was 12°, and the distance between the SSD and the propeller disc was 40mm, the received power decreased the most, the value reduced from 7076 to 6810, the amplitude reduction was 3.8%.

The heat flux for the YPSZ/NiCrAl-coated from FEA exhibited about 98% reduction compared to the uncoated piston crown.
The data of the engine is based on a spark ignition engine with four-stroke cycle with direct injection system and CNG fuelled [15−17].
Ariffin, Friction Reduction in Compressed Natural Gas Direct Injection Engine using Piston Rings with Diffusion Chromium Coating, J.