Papers by Author: Chang Sheng Xie

Paper TitlePage

Authors: Kai Jin Huang, Li Yan, Chang Sheng Xie
Abstract: Based on the principle of the higher surface-to-volume ratios, the higher formaldehyde gas sensitivity, different morphologies’s ZnO nanostructures have been synthesized by hydrother- mal method using different surfactants including polyvinyl alcohol (PVA), cetyltrimethyl ammon- ium bromide (CTAB), sodium tripolyp hosphate (STPP) and citric acid(CA). The crystal structur- es and morphologies were characterized by XRD and FESEM. The results show that different morphologies’s ZnO nanostructures were induced on the surface of alumina substrate, and the surfactants had an important effect on the morphologies of ZnO nanostructures and then affected the formaldehyde gas sensitivity. The ZnO nanorods with diameters of 100-500 nm and lengths of 200-900nm were obtained using PVA surfactant. The ZnO nanosheets with thickness of about 10nm were obtained using CTAB surfactant. The ZnO nanodisks with two layers and thickness of 5-10nm were obtained using STPP surfactant. The ZnO microspheres composed of thin flakes with thickness of about 10 nm were obtained using CA surfactant. The growth mechanisms of different morphologies’s ZnO nanostructures using different surfactants were given in detail. In addition, the formaldehyde gas sensitivities of different morphologies’s ZnO nanostructures were measured and showed the higher formaldehyde gas sensitivity compared with nano-ZnO without surfactant.
628
Authors: Kai Jin Huang, Li Yan, Chang Sheng Xie
Abstract: The nano γ-Fe2O3/ZnO double-layer film gas sensor was fabricated by the screen printing technology and the hydrothermal method. XRD and SEM techniques were used to characterize the phases and morphologies of the film. The gas sensing properties of the gas sensor to ethanol were investigated. The result shows that the gas sensitivity of the gas sensor is higher than that of the nano γ-Fe2O3 single-layer film gas sensor and the nano ZnO single-layer film gas sensor. The high gas sensitivity of the nano γ-Fe2O3/ZnO double-layer film to ethanol was caused by the combined effect and nano effect.
602
Authors: Kai Jin Huang, Cun Shan Wang, Chang Sheng Xie
Abstract: To improve the wear property of magnesium alloy, wear-resistant TiC and in-situ ZrC co-reinforced Zr-based amorphous composite coating has been fabricated on AZ91D magnesium alloy by laser cladding using mixed powders of Zr52.5Cu17.9Ni14.6Al10Ti5-TiC. The microstructure of the coating was characterized by XRD and SEM techniques. The wear resistance of the coating was evaluated under dry sliding wear test condition. The results show that the coating mainly consists of amorphous and different crystalline phases. The coating exhibits excellent wear resistance due to the recombination action of amorphous and crystalline phases, and the wear resistance improves further with the increase of TiC content. The main wear mechanism of the coating and the AZ91D sample are different, the former is abrasive wear and the latter is adhesive wear.
206
Authors: Kai Jin Huang, Chao Dong Tan, Chang Sheng Xie
Abstract: The HTPB-coated aluminum nanopowders were prepared by using horizontally-mounted kneading machine. The HTPB-coated aluminum nanopowders were characterized by TEM, XRD and FTIR. The exothermic characterization of the HTPB-coated aluminum nanopowders was analysized by simultaneous TG-DSC. The results show that the HTPB-coated aluminum nanopowders have a core-shell structure and the release heat enthalpy in pure oxygen is 4.954KJ/g at 542.7°C. The stability of HTPB-coated aluminum nanopowders excelled Al2O3-passivated aluminum nanopowders due to the hydrophobic nature of HTPB and the hydrophilic nature of Al2O3.
189
Authors: Kai Jin Huang, Li Yan, Hua Min Kou, Chang Sheng Xie
Abstract: Based on the combined toughening principle, pure Al2O3/AlB12/Al composite ceramic powders have been synthesized using a new laser-induction complex heating method. This method starts from Al and B2O3 powder mixtures, after which Al2O3/AlB12/AlN composite ceramics were fabricated by hot-press sintering at 1600°C for 2h under the protection of a N2 atmosphere. XRD and SEM techniques were used to characterize the phases and morphologies of the powders and the ceramics. The bending strength and the fracture toughness of the ceramics were measured by the three-point bending method and the indentation fracture method, respectively. The results show that the pure Al2O3/AlB12/Al composite ceramic powders can be successfully synthesized by this new laser-induction complex heating method because the adiabatic temperature of Al-B2O3 system is more than 1800K. Al2O3 and AlB12 phases were formed by the liquid-liquid reaction mechanism and the liquid-solid reaction mechanism, respectively. The bending strength and the fracture toughness of the Al2O3/AlB12/AlN composite ceramics were 551.44MPa and 6.04MPa.m1/2, respectively. These values are 57.55% and 51% greater than those of the pure Al2O3 ceramic (350MPa and 4MPa.m1/2) due to the reinforcing and toughening in-situ formation of small AlN particles.
596
Authors: Kai Jin Huang, Hou Guang Liu, Chang Sheng Xie
Abstract: The ternary solid solution BiOCl0.2Br0.1I0.7 was successfully synthesized using a wet chemical method. The visible light photocatalytic properties of BiOCl0.2Br0.1I0.7 were investigated for the first time. Powder samples were characterized by XRD, SEM, UV-vis spectrophotometry and nitrogen sorption. BiOCl0.2Br0.1I0.7 absorbs intensely in the visible light region and the optical bandgap is 1.82eV. The chlorine and the bromine elements have an obvious effect in changing the bandgap energy and the particle size of the catalysts. The deep valance band edge position, the internal electric fields and the morphology give the BiOCl0.2Br0.1I0.7 best visible light photocatalytic properties.
2094
Authors: Ai Hua Yan, Chang Sheng Xie, Fei Huang, Hua Yao Li, Shao Liang Zhang
Abstract: Tungsten trioxide (WO3-x) with different morphologies was synthesized by hydrothermal method. Using a pair of Pt electrodes and Al2O3 ceramics tube as a substrate, NO2 sensing properties of the WO3 products were measured at different working temperatures. And the high sensing properties at low working temperature were also investigated. The results showed that the sensitivity of WO3 product is strongly dependent on morphology and structure. The parallel circuit mode also plays an important role in the NO2 sensing characteristics. The low working temperature can be attributed to the competitive reaction between O2 and NO2 gas. The parallel mode may increase the lifetime of sensor.
3866
Showing 1 to 7 of 7 Paper Titles