Papers by Author: Colin Leach

Paper TitlePage

Authors: Z. Ling, Colin Leach, Robert Freer
1465
Authors: T. Hussain, Ali Gholinia, Colin Leach
544
Authors: Hiroaki Takeda, Han Joong Sang, Takashi Tateishi, Spela Kunej, Colin Leach, Robert Freer, Takuya Hoshina, Takaaki Tsurumi
Abstract: BaTiO3–(Bi1/2K1/2)TiO3 (abbreviated as BT-BKT) solid solution ceramics, as a lead-free PTC (positive temperature coefficient of resistivity) thermistor material usable over 130°C, has been synthesized by sintering in N2 atmosphere and after annealing in air over 1200°C. In the BT-BKT ceramics with PTC property, the impedance/modulus spectroscopic plots have revealed that a third resistance-capacitance (RC) response besides grains and grain boundaries. Using the remote electron beam induced current (REBIC) configuration, imaging has revealed EBIC contrast consistent with the presence of negatively charged electrostatic grain boundary barriers in the BT-BKT semiconducting ceramics.
241
Authors: J.D. Russell, Colin Leach, Robert Freer
1155
Authors: F. Azough, Colin Leach, Robert Freer
Abstract: Ba(Me1/3Nb2/3)O3 (Me=Zn, Co, Ni and Mg) ceramics were prepared using the conventional mixed oxide route; additives included Al2O3, Ga2O3, SiO2, WO3, B2O3 and V2O5. Powders were mixed, milled for 18h, calcined at 1100°C, remilled pressed into pellets at 100 MPa, sintered in air at temperatures in the range 1350-1550°C and then cooled at 360C h–1 to 5°C h–1. Products were characterised in terms of phase analysis (X-ray diffraction), microstructure (SEM and TEM) and electrical properties (relative permittivity, εr, dielectric Q value and temperature coefficient of resonant frequency,τf). The Q values of the Ba(Me1/3Nb2/3)O3 ceramics depend on the degree of cation ordering and the additives. Slow cooling leads to 1:2 ordering of the B sites and enhanced dielectric Q values. For samples cooled at 5°C h–1 after sintering the Qxf values are in the range 28000 to 98000 GHz, and are in the sequence Ba(Ni1/3Nb2/3)O3, Ba(Co1/3Nb2/3)O3, Ba(Mg1/3Nb2/3)O3 and Ba(Zn1/3Nb2/3)O3. Additions of BaO-4WO3 or V2O5 yield higher Qxf values than Al2O3. Highly ordered Ba(Zn1/3Nb2/3)O3 has a relative permittivity of 39.4, but most other Ba(Me1/3Nb2/3)O3 ceramics exhibit εr of 31-32. The temperature coefficient of resonant frequency, τf, varies from –18 ppm/°C (Ba(Ni1/3Nb2/3)O3) to +32 ppm/°C (Ba(Mg1/3Nb2/3)O3); the sintering additives (Al2O3 and BaO-4WO3) change τf by typically 10-16 ppm/°C.
2323
Authors: Z. Ling, Colin Leach, Robert Freer
1461
Authors: Colin Leach, M. Zubair, Robert Freer
Abstract: A series of PTC thermistors, based on BaTiO3, doped with Ca, Mn and Y, were prepared with additions of SiO2 at levels of 0, 1, 2 and 3 at. %. The effect of the SiO2 additions and cooling rate on microstructural development and bulk performance were characterised using a combination of SEM, EBSD, and R-T experiments. It was found that the addition of SiO2 increased grain size marginally, and decreased sample density by reducing the amount of grain-grain contact. The addition of SiO2 also modified the distribution of grain boundary types by systematically decreasing the proportion of low-Σ grain boundaries within the microstructure. Electrical behaviour was modified by adding SiO2 or increasing the sample cooling rates; in both cases there was an increase in ρ25 and a decrease in ρmax, with ρmax also being displaced to higher temperatures.
2362
Showing 1 to 10 of 11 Paper Titles