Papers by Author: Jie Wu Zhu

Paper TitlePage

Authors: Ya Ni Zhang, Chang Zheng Xu, Mao Sheng Zheng, Jie Wu Zhu
Abstract: The corrosion resistance of Ultra-fine grain (UFG) chromium bronze, prepared by Equal-channel angular pressing (ECAP), was investigated at room temperature and atmospheric pressure by electrochemistry technique and immersion experiment. The electrochemistry experiment showed that ECAP processing don’t change the corrosion nature of chromiun bronze, the corrosion potential of UFG chromium bronze is a little more positive than that of CG chromium bronze, the differences are in the range of 10mV-20mV. Meantime, the immersion experiment showed that the UFG chromium bronze is more resistant to corrosion than its CG counterpart. The difference between UFG chromium bronze and its CG counterpart is also significant in terms of corrosion morphology. Though the structure is uniform corrosion, the microstructure is honeycomb-like morphology for CG chromium bronze and the corrosion pit is deeper. The shallower corrosion pits are displayed for UFG chromium bronze and grain drop off in local region.
554
Authors: Yong Ning Liu, Jie Wu Zhu, Yan Xu
Abstract: 1.4 %C ultra high carbon steel (UHCS) was prepared in order to study the structure of martensite transformation and mechanical properties. Ultra-fine spherical carbide and ultra-fine austenite grain size were obtained. A great deal of lath martensite was observed after quenching. The phenomenon does not agree with the traditional knowledge that the lath martensite would disappear when carbon content is in excess of 0.8% in austenite. The strength, fatigue properties and fracture toughness have been measured. A good combination of strength, toughness and fatigue properties come from fine and uniform distributed carbide particles and ultra-fine austenite grain size. Fracture strength increases by 48%, yield strength increases by 15% and plasticity keep the same comparing with that of hardened and tempered 40CrNiMo. The carbon content of ultrahigh carbon steels (UHCS) is in the range of 1.0-2.1% [1, 2]. Traditional heat treatments for normal steels will cause the microstructure of UHCS to be coarse and do not produce optimal properties. With controlled rolling and special heat treatment, UHCS can be in ferrite, pearlite, bainnite or martensite structures, which all have different mechanical properties. The yield stress of a 1.8%C, 1.6%Al ferrite UHCS can reach 1500MPa, which is much higher than that of high strength and plain alloy steels [3]. The tensile strength of a 1.25%C-1.5%Cr pearlite UHCS can reach 1810Mpa and its elongation can be 18%. When it is treated into martensite, its compression strength reached to 4690Mpa and compression strain reached to 26% [1, 4], which is comparable to WC-12Co. Such good mechanical properties can be ascribed to the ultra fine grain sizes because of the undissolved carbide particles which resist growth of austenite grain during heating. Another reason could be the lath martensite structures. O.D.Sherby [4] had reported that there was a lot of lath martensite in quenched UHCS. The UHCS was considered not only as tool steels but also as good structure materials. Fracture and fatigue properties are important for structure materials. However, they have rarely been studied. The present paper is going to study the martensite structure and mechanical properties of a prepared 1.4% C UHCS.
1178
Authors: Wei Ping Lin, Ya Jun Fan, Zhan Ling Zhang, Jie Wu Zhu, Yong Ning Liu
Abstract: A ultrahigh carbon steels (UHCS) containing 1.6 wt pct carbon was studied. Through spheroidizing process by divorced-eutectoid transformation (DET), the forged microstructure was spheroidized and the microstructure was fine carbide particles distributed in ferrite matrix. Second-time heat treatment included two kinds of technologies: normalizing and quenching + tempering. Finally, the UHCS obtained ideal mechanical properties. The yield strength and tensile strength of the UHCS were higher than that of 40CrNiMo, moreover plasticity of the UHCS was equal to that of 40CrNiMo. So the UHCS was an excellent structural material.
907
Authors: Zhan Ling Zhang, Yong Ning Liu, Jie Wu Zhu, G. Yu
Abstract: Ultrahigh carbon steel containing 1.6 wt pct C was processed to create microduplex structure consisting of fine-spheroidized carbides and fine ferrite grains. Elongation-to-failure tests were conducted at strain rates from 10-4s-1 to 15×10-4s-1, and at temperatures from 600 °C to 850 °C. The steel exhibited superplasticity at and above 700 °C when testing at a strain rate of 10-4s-1, and at 800 °C when testing at strain rates of 7×10-4s-1 and slower. The grains retained the equiaxed shape and initial size during deformation; dynamic grain growth was not observed after superplastic deformation, whereas carbide coarsening was observed. It is concluded that the fine ferrite grains or austensite grains are stabilized by the grain boundary carbides, and grain-boundary sliding controlled by grain boundary diffusion is the principal superplastic deformation mechanism at temperatures in the range of 700-850 °C.
199
Showing 1 to 4 of 4 Paper Titles