Papers by Author: Mario Guagliano

Paper TitlePage

Authors: Sara Bagherifard, Ramin Ghelichi, Mario Guagliano, M. Bandini
Abstract: The effect of slight surface REM finishing, that is a chemically accelerated polishing process, in order to reduce surface roughness after shot peening has been studied on different series of specimens shot peened by varied peening parameters. Room temperature rotating bending fatigue tests have been performed on the shot peened series and the series subjected to shot peening and successive REM finishing process. The results represent how REM finishing affects the final fatigue behavior of differently treated specimens in two ways: decreasing surface roughness and removing a thin layer of material with compressive residual stresses.
290
Authors: Sara Bagherifard, Ines Fernàndez Parienete, Ramin Ghelichi, Mario Guagliano, Simone Vezzù
Abstract: Coating deposition processes such as cold spraying are commonly employed to increase wear and fatigue resistance and consequently to enhance longevity of engineering components. Such processes typically introduce residual stresses into the coated surface, which in turn affect efficiency of coatings and play an important role in coating durability. Present study describes alteration of residual stress state and surface work-hardening of two types of aluminum coatings that are cold sprayed onto aluminum substrate, and subsequently treated by air blast shot peening (ABSP). Residual stress measurements have been made by means of X-ray diffractometer (XRD) on coated samples both before and after shot peening process. The results indicate that that the effect of shot peening is more marked in terms of surface work-hardening than of residual stresses and allow some consideration to correctly orient the choice of peening parameters in practical application.
397
Authors: Mario Guagliano, Sara Bagherifard, Ines Fernàndez Parienete, Ramin Ghelichi
Abstract: Surface grain refinement is a relatively new process aimed to enhance mechanical material properties. In this study Al7075-T6 bars have been shot peened with parameters much different from those of conventional shot peening. Microstructure gradient has been observed by means of transmission electron microscopy (TEM), X-ray diffraction (XRD) and nano indentation tester. A fine grained layer was found on top surface of the specimens. Measurements indicate of notable improvements in cases of hardness and elastic modulus in comparison with untreated material. XRD results also show significant depth affected both in terms of residual stress and FWHM. The results imply that using optimized shot peening parameters, it would be possible to create a fine grained layer on surface of component and consequently increase fatigue life and any other property affected by grain size.
393
Authors: Mario Guagliano
Abstract: The effectiveness of the application of shot peening after nitirding for improving the fatigue strength of high-performance steel components has not been adequately treated in literature, and it is not clear if shot peening can really and drastically increase mechanical performances of nitirded elements. In this paper an approach to assess the influence of shot peening on nitrided components is presented. It is based on fracture mechanics concepts. Smooth specimens with a micro-hole acting as a pre-crack were fatigue tested. The values of micro-hardness and of the residual stresses were measured and related to the experimental results. By elaborating the results it was possible to determine the threshold values of the stress intensity factors of the nitrided and shot peened material. A formula to predict the value of Kth of shot peened and nitrided steels is proposed.
865
Authors: Mario Guagliano, Majid R. Ayatollahi, Mahnaz Zakeri, Chiara Colombo
Abstract: According to classical definition of crack deformation modes, the constant stress term (Tstress) exists only in presence of mode I. However, some studies show that this term can exist in mode II problems as well; and significantly affect the elastic stress field around the crack tip. Based on the previous analytical results, T-stress changes the photoelastic fringe patterns from symmetric closed shapes to asymmetric and discontinuous loops. In this research, the effects of T-stress on the fringe patterns in mode II cracks is investigated experimentally. Test specimens are Brazilian disks made of polycarbonate, and thermal treatment is performed to remove the residual stresses after generation of the cracks. Observed isochromatic fringes are in good agreement with theoretical predictions. Also, experimental results indicate that this specimen contains a negative T-stress in pure mode II condition.
969
Authors: Seyyed Mostafa Hassani-Gangaraj, A. Moridi, Mario Guagliano
Abstract: Recent development in mechanical technologies and processes have shown that by performing traditional mechanical treatments with unusual and severe parameters it is possible to obtain metal surfaces characterized by grain size with dimension in the order of 50-100 nm. This confers peculiar and superior properties to the surface layer of material. Since the surface is the usual point of fatigue crack initiation it is expected that the parts treated this way show a better fatigue behavior with respect to the coarse grain materials, even if treated with conventional mechanical treatments. This work explores any opportunities to obtain nano-structured surface layers by means of two popular mechanical treatments, shot peening and deep rolling. To this end particularly severe processing parameters are applied on a low alloy steel fatigue test specimens. The treated surface is characterized by means of optical Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD) analysis of residual stress and roughness measurements. In the end a series of fatigue tests on smooth specimens severely treated, conventionally treated and not treated were executed. The results show the potential benefits of severe mechanical treatments and were interpreted in the light of peculiar effects of these novel treatments on the characteristics of the treated surfaces.
469
Authors: Chiara Colombo, Mario Guagliano, Laura Vergani
1321
Authors: Ines Fernández Pariente, Sara Bagherifard, Ramin Ghelichi, Mario Guagliano
Abstract: Effects of surface defect size and the method used to obtain the defect itself on bending fatigue behaviour of nitrided and shot peened steel was studied. Two different series of 15 sandglass specimens with a microhole in the minimum section generated after nitriding and shot peening treatments were considered. In one series the microholes were obtained by controlled electro-erosion. In the other series microholes were obtained by indentation, much more invasive that electro-erosion, simulating a damage due to a mechanical impact or scratch on the surface material, common on real components during the life span. In both cases the microholes act as a pre-existent crack. The results show that defects obtained by indentation lead to a minor fatigue limit with respect of larger defects obtained by electro-erosion. This was interpreted as the modification of the residual stress field due to the mechanical indentation. On the basis of the results some consideration is formulated about generating micro-holes with one of the discussed ways.
57
Authors: Mario Guagliano, Laura Vergani
Abstract: In this paper the fatigue crack growth properties of a nitrided shot-peened steel is dealt with: different peening intensities were considered and the resulting residual stresses measured by means of an X-ray diffractometer. Rotating bending fatigue tests were executed on specimens with a blind micro-hole, acting as a pre-existent crack. The results allowed determining the threshold of propagation of the nitrided and of nitrided and shot peened material. It was also possible to relate the crack initiation point with the applied and the residual stresses.
375
Showing 1 to 10 of 12 Paper Titles