Papers by Author: Ruth Cameron

Paper TitlePage

Authors: Z. Yang, E.S. Thian, Serena Best, Ruth Cameron
Abstract: α-tricalcium phosphate (α-TCP) was prepared by a wet precipitation reaction between calcium hydroxide and orthophosphoric acid solutions. The as-synthesised powder was then characterised using a Scanning Electron Microscope (SEM) equipped with Energy Dispersive Spectroscope (EDS), X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscope (FTIR). Analyses revealed that a phase-pure powder with a Ca/P ratio of 1.5 was produced. In addition, nanosized α-TCP particles of diameter ~ 70 nm were agglomerated to form larger particles of 10μm in diameter. It was found that by the combination of attritor milling and solution evaporation, the agglomerates of α-TCP nanoparticles could be broken down, and distributed evenly within the poly(D,L-lactic-co-glycolic acid) (PLGA) matrix. Thus, a α-TCP/PLGA nanocomposite was successfully produced by a modified solution evaporation method at room temperature followed by hot pressing at 150 °C. The achievable ceramic loading was approximately 38 wt.%, which was confirmed by thermal gravimetric analysis (TGA).
511
Authors: Z. Yang, E.S. Thian, Roger A. Brooks, Neil Rushton, Serena Best, Ruth Cameron
Abstract: In this study, a biocomposite comprising nanostructured α-tricalcium phosphate (α-TCP) in a poly(D,L-lactic-co-glycolic acid) (PLGA) matrix was fabricated by a modified solution evaporation method. As a potential temporary bone fixation and substitution material, its bioactivity was evaluated by its ability to form bone-like apatite layer in simulated body fluid (SBF). Owing to the increased surface area covered by the osteoconductive bioceramic of α-TCP, rapid apatite formation was observed. After 7 days of immersion, enhanced nucleation of apatite was observed on the nanocomposite. At day 14, dense lamellar-like apatite was formed on the nanocomposite whilst apatite nucleation had only just started to develop on the surface of pure PLGA. At the same time, a preliminary in-vitro cell culture study was conducted using human osteoblast-like (HOB) cells. A significant increase in cell number with culturing time was observed for the nanocomposite. After 9 days incubation, a confluent lamellar-like apatite layer was formed on the composite surface. This apatite layer was also shown beneath the proliferating HOB cells at Day 16.
459
Authors: Duygu Ege, Koonyang Lee, Alexandre Bismarck, Serena Best, Ruth Cameron
Abstract: The aim of this work is to produce and characterise carbonate substituted hydroxyapatite (CHA) reinforced polycaprolactone (PCL) nanocomposites with a controlled degradation rate in order to match the rate of bone in-growth. The ideal degradation time for this purpose is estimated to be around 5-6 months however, in vivo, PCL degrades over a period of 2 to 3 years. It has been reported that NaOH surface treatment can accelerate the degradation of PCL [1-3]. In order to further modify the degradation rate of PCL, the effects of the incorporation of different volume fractions of CHA in samples surface treated with NaOH was investigated. CHA was produced by wet chemical synthesis. Samples comprising 8, 19, 25 wt% uncalcined CHA-PCL composites were produced by twin screw extrusion which were then injection moulded into cylinders. In order to accelerate the degradation rate of PCL, it was surface treated with 5 M NaOH for 3 days prior to PBS studies. The degradation profile was examined by % weight loss and % water uptake measurements. NaOH treatment was observed to erode the polymer surface and the polymer-filler interface. On subsequently degrading the pre-treated samples in PBS, it was observed that with increasing fraction of CHA, the degradation rate in PBS of the sample increased. Up to 8 wt % CHA filler there appeared to be little change in the degradation properties of the NaOH treated samples with the onset occurring after 60 days. However there was a marked acceleration of degradation for samples containing 19 wt% when degradation appeared to occur immediately. In conclusion, the addition of CHA significantly affects the behaviour of PCL.
120
Authors: Lisa M. Ehrenfried, David Farrar, David Morsley, Ruth Cameron
Abstract: Co-continuous degradable polymer-ceramic composites were produced via in-situ polymerization of (D,L-lactic)acid monomer within a porous β-tricalcium phosphate matrix. The mechanical properties of both the composite and the unfilled porous ceramic were investigated with compressive testing. The average stress to failure increased from 1.3±0.1 MPa for the unfilled ceramic matrix to 82±2 MPa for the composite. The Young’s modulus increased from approximately 20 MPa to 700±42 MPa. A combination of X-ray micro-tomography and mechanical testing provided insight into the failure mechanisms of the composite. Stress may be deflected by crack bridging around the polymer phase leading to debonding of the polymer along the crack lines.
407
Authors: Liang Hao Han, James Elliott, Serena Best, Ruth Cameron, A.C. Bentham, A. Mills, G.E. Amidon, B.C. Hancock
Abstract: In this paper, we present a modified density-dependent Drucker-Prager Cap (DPC) model with a nonlinear elasticity law developed to describe the compaction behavior of pharmaceutical powders. The model is implemented in ABAQUS with a user subroutine. Using microcrystalline cellulose (MCC) Avicel PH101 as an example, the modified DPC model is calibrated and used for finite element simulations of uniaxial single-ended compaction in a cylindrical die. To validate the proposed model, finite element simulation results of powder compaction are compared with experimental results. It was found that finite element analyses gave a good prediction of both the loading-unloading curves during powder compaction and the compaction force required for making a tablet with a specified density. Further, the failure mechanisms of chipping, lamination and capping during tabletting are investigated by analysing the stress and density distributions of powders during the three different phases of the tabletting processes, i.e. compression, decompression and ejection. The results indicate that the model has excellent potential to describe the compaction process for generic pharmaceutical powders.
560
Authors: A.K. Lynn, Ruth Cameron, Serena Best, Roger A. Brooks, Neil Rushton, William Bonfield
593
Authors: Julian R. Jones, Georgina E. Milroy, Ruth Cameron, William Bonfield, Larry L. Hench
Abstract: Bioactive glass scaffolds with interconnected macroporous networks have been developed by foaming sol-gel derived bioactive glass of the 70S30C (70 mol% SiO2, 30 mol% CaO) composition. The effect of sintering temperature on the dissolution of the scaffolds in simulated body fluid (SBF) was investigated in 3D using x-ray micro-computer tomography (micro CT) and inductive coupled plasma (ICP) analysis. Micro-CT is non-destructive and allows observation of specific parts of the scaffold at various stages of degradation. However, data analysis is complex at present. Percentage porosity data obtained by micro-CT was compared to physical data and pore size distributions obtained from mercury intrusion porosimetry were compared to the interconnected pore diameters observed from the micro CT images.
493
Authors: F.F. Rahman, William Bonfield, Ruth Cameron, M.P. Patel, M. Braden, G. Pearson, S.M. Tavakoli
513
Showing 1 to 8 of 8 Paper Titles