Papers by Author: Un Bong Baek

Paper TitlePage

Authors: Un Bong Baek, Jong Seo Park, In Hyun Chung, Seung Hoon Nahm, Young Hwa Ma, Yong Yun Lee
Abstract: The high cycle fatigue properties of two kinds of wrought Al 2519 alloys without and with scandium of 0.10% were investigated. The fatigue strength was determined at R = 0.1 under constant amplitude loading conditions in air. The alloy with scandium of 0.10% showed a little lower tensile yield strength and higher fatigue strength values. The fine grained Al-0.10Sc alloy exhibited a higher resistance against fatigue crack nucleation despite the lower yield stress in comparison to the coarse grained Al 2519 alloy. The results can be explained mainly with the microstructural differences between both alloys. This results are due to the presence of coherent Al3 (Sc, Zr) precipitates and a very fine subgrain structure.
2483
Authors: Un Bong Baek, Jong Seo Park, In Hyun Chung, Tae Won Park, Seung Hoon Nahm
Abstract: Al alloy is used extensively in several fields because specific strength is good and workability is superior. It is known that If Sc is added to Al alloy, strength is increased and re-crystallization temperature rises because microstructure becomes fine. The high cycle fatigue properties of four kinds of Al-Mg-Si alloys without and with only scandium of 0.20 % or with both scandium(Sc) of 0.20 % and zirconium(Zr) of 0.12% were investigated. The fatigue strength was determined at R = -1.0 under constant amplitude loading conditions in air. The alloy with scandium of 0.20 % showed a little higher fatigue strength values. The alloy with 0.20 % Sc and 0.12 % Zr showed highest tensile yield strength and highest fatigue strength. The fine grained Al 6061+0.20Sc+0.12Zr alloy exhibited a higher resistance against fatigue crack nucleation in comparison to the coarse grained Al 6061 alloy. The results can be explained mainly with the micro-structural differences among four alloys. This results are due to the presence of coherent Al3 (Sc, Zr) precipitates and a very fine sub-grain structure.
657
Authors: Un Bong Baek, Jong Seo Park, Seung Hoon Nahm, Hyuck Mo Lee
Abstract: In spite of frequent defect in industrial boilers, life assessment or diagnostic method for them has not been studied. In this research, SB410 carbon steel used in industrial boilers is simulated with artificial aging heat treatment. To do qualitative life assessment, differences in micro-structures and hardness of SB410 by the degradation time are studied. In addition, variation in material properties by aging was observed with the tensile test at room temperature and 179 °C and changes in ductile to brittle transition temperature was observed with the charpy impact test performed at several test temperature.
532
Authors: Jong Seo Park, Un Bong Baek, Jeong Min Kim, Seung Hoon Nahm, Bong Young Ahn
Abstract: Several nondestructive evaluation methods were attempted for the estimation of the creep damage of degraded 2.25Cr-1Mo steel. The specimens of three different aging periods were prepared by an isothermal heat treatment at 430°C, 482°C, and 515°C. The effect of probe configuration on the electrical resistivity was studied. Single configuration method and dual-configuration method were utilized for measuring electrical resistivity. The electrical resistivity was determined by a standard DC four-point probe method at 24±0.5°C. Indentation test, magnetic characteristics test and ultrasonic test were carried out to investigate the correlation between the major characteristics and aging parameter. Unlike the electrical resistivity characteristics, ultrasonic attenuation coefficient and indentation characteristics did not show a relation to Larson-Miller parameter. However, a correlation between the electrical resistivity and aging parameter was identified, which allows one to estimate the extent of material degradation.
1951
Authors: Jong Seo Park, Un Bong Baek, Seung Hoon Nahm, Sang In Han, Song Chun Choi
Abstract: The nondestructive evaluation technique for the material degradation is necessary because of the limitation of conventional destructive methods. In this study, an ultrasonic velocity measurement method was attempted for the estimation of the creep damage of degraded modified 9Cr-1Mo steel. The specimens with seven different kinds of aging periods were prepared by an isothermal heat treatment at 690 . The ultrasonic velocity was measured by an immersion method. The correlation between the measured ultrasonic velocity and tensile properties were studied. The ultrasonic velocity has an declining tendency with the increase of heat treatment time. A correlation between the ultrasonic velocity and aging parameter were established, which allows one to estimate the material degradation of modified 9Cr-1Mo steel.
528
Showing 1 to 5 of 5 Paper Titles