Papers by Author: Xiao Chuan You

Paper TitlePage

Authors: Xiu Gen Jiang, Yang Yang, Feng Jie Zhang, Jin San Ju, Xiao Chuan You
Abstract: Nonlinear finite element model analysis of the casing plug joints of steel tubular has been realized by ANSYS software. The law of load-carrying capability and stiffness of joint are separately gained by changing the ratio of length and diameter (R/L) and the ratio of the casing length and the main tube length (l/L). The influence of the casing thickness on the load-carrying capability and stiffness are also discussed. The results indicated that the load-carrying capability and stiffness of the joints both increase with the ratio(R/L) increment and the ratio of the casing length and main tube length (l/L). When the main tube thickness is equal to casing thickness, the load-carrying capacity of joints achieves the most.
321
Authors: Zhuo Zhuang, Zhan Li Liu, Xiao Chuan You, Y. Guo
Abstract: With the development of material science, especially as MEMS/NEMS are playing a more and more important role in modern engineering, some mechanical behaviors of materials, e.g., fracture, shear instability, need to be investigated from multidisciplinary perspective. The molecular dynamics (MD) simulations are performed on single-crystal copper block under simple shear to investigate the size and strain rate effects on the mechanical responses of face-centered cubic (fcc) metals. It is shown that the yield stress decreases with the specimen size and increases with the strain rate. Based on the theory of dislocation nucleation, a modified power law is proposed to predict the scaling behavior of fcc metals. In the MD simulations with different strain rates, a critical strain rate exists for each single-crystal copper block of given size, below which the yield stress is nearly insensitive to the strain rate. A hyper-surface is therefore formulated to describe the combined size and strain rate effects on the plastic yield stress of fcc metals.
875
Authors: Jin San Ju, Xiao Chuan You, Xiu Gen Jiang, Jin Zhao Zhuang
Abstract: This paper primarily describes the development and application of substructure computational analysis techniques to determine stress intensity factors for the damaged panels subjected to fatigue internal pressure. A program based on substructure analysis technique has been developed for the fracture analysis of curved aircraft panels containing cracks. This program may create whole model which consists of substructure superelements and obtain fracture parameter of the crack by expanding results in superelement automatically. For instance, a typical test curved panel model consists of 7 frames and 8 stringers is calculated. This numerical approach has been validated through comparison between the calculation SIF results and available experimental data of a typical test panel with a longitudinal crack. The technique that has been established here is also applied to the other analysis of a test series of cracked panel with 7 frames and 10 stringers. SIFs of four cracks in it with different crack lengths are obtained efficiently.
29
Authors: Chun Yang Liu, Bing Xin Li, Jin San Ju, Xiu Gen Jiang, Xiao Chuan You
Abstract: The explicit numerical method is used to trace the impact procedure of the tube columns impacted by a rigid body. The bar and rectangle tube models are both used to simulate the tube column. The elastic and elas-plastic impact load with different mass ratio and impact speed are obtained. The calculation results show that: for elastic models, the bigger the mass ratio and the higher the rigid body speed, the bigger the peak value of elastic impact load; at the same time, the more obvious the reduction effect of local buckling of rectangle tube on the peak value of impact load and the longer the contact time of tube model; so the peak value of impact load of the rectangle tube is not proportional to the rigid body speed. The stress wave in the tube causes a little difference between the load curves of tube model and bar model. For elas-plastic models, the higher the rigid body speed and the smaller the mass ratio, the bigger the peak value of impact load and the longer the contact time. The higher the rigid body speed, the bigger the difference between elastic and elas-plastic impact load peak value due to the expanding of plasticity. Because of the effect of local buckling, the peak value of elas-plastic impact load of rectangle tube is always lower than that of bar.
363
Authors: Yong Wen Lin, Xiao Chuan You, Zhuo Zhuang
Abstract: In this article we presented a method of Fluid-Solid coupled simulation via FLUNET and ABAQUS in problems such as Aero/Hydro-Elasticity problems. UDF (user define function) script file in the Fluent software was utilized as the ‘Connecting File’ between FLUENT and ABAQUS for Aero-Elastic computations. Firstly, the fluid field was computed by Navier-Stokes Equation and the structure movement was directly integrated by the dynamics Equation, respectively. Then, the ‘Connecting File’ exchanged the computed data through the fluid and structure’s interface. The next analysis step continued. Analysis of the computed results showed that this coupling method designed for aero-elastic system was feasible and can be also used for other Fluid-Structure Coupling problems.
1095
Showing 1 to 5 of 5 Paper Titles