Papers by Keyword: Intake Manifold

Paper TitlePage

Authors: Fu Guo Zhao
Abstract: This paper is an overview of research about variable intake manifold in the past 12 years. First, a brief introduction to the basic principle of the variable intake is given.Then, the research of variable intake manifold in these years is presented and discussed, and the important studies are described in detail. Finally, the paper gives a summary of the research status and prospects of variable intake manifold.
299
Authors: Mohd Faisal Hushim, Ahmad Jais Alimin, Mohd Farris Mansor
Abstract: Fuelling system is one of the crucial variables that must be focused on, in order to achieve good fuel efficiency and low engine out emissions. Fuel injection system seems a promising technology as a medium to supply suppressed fuel because of its high fuel delivery efficiency, enhanced fuel economy and reduced engine out emission. Port-fuel injection (PFI) system has been used widely on small four-stroke gasoline engine because of its simplicity compared to direct injection (DI) system. In this study, the effects of intake manifold angle of a PFI retrofit-kit to the engine performances and emission characteristics were investigated. Experimental works comprised wide-open throttle with variable dynamometer loads for two different angles: 90° and 150°. From this study, it was observed that 150° was the best angle, which produced high brake power (BP) and brake mean effective pressure (BMEP), brake specific fuel consumption (BSFC) and hydrocarbon (HC) emission.
31
Authors: Mohd Taufiq Muslim, Hazlina Selamat, Ahmad Jais Alimin, Mohd Faisal Hushim
Abstract: Most motorcycles in developing countries use carburetor systems as the fuel delivery method especially for models with the cubic capacity of less than 125cc. However, small gasoline fuelled engines operating using carburetor system suffer from low operating efficiency, waste of fuel and produce higher level of hazardous emissions to the environment. In this study, an electronic control unit (ECU) is designed and simulated for a retrofit fuel injection (FIS) system. The ECU is targeted to have a simple design, reliable and offers all of the necessary functions of the modern ECU. The simulation results shows that the designed ECU can determine the injection period as close to the proposed value and can drive the injector efficiently based on the generated PWM pulse.
968
Authors: Cai Yun Wang, Zhi Xia He, Qian Wang, Guo Jun Zhang, Shuo Wang
Abstract: The performance of the engine air intake system directly affect the working performance and fuel consumption, where the intake manifold design is the key.In this paper aimed at L91 Engine intake manifold ,firstly theRE(Reverse Engineering)technology was usedto rebuild the3d model of intake manifold.And then the internal flow zoneof the intake manifoldwas meshedin the pre-processing software ICEMand the internal flow fieldwas analyzedin the softwareof Fluent.The numerical model was verified by comparing the simulated and measured results. And then based on the numerical analysis of the internal flow characteristics of the intake manifold, the structure of variable-length intake manifold was come up with and finally was numerically proved to be better than the normal one.
930
Authors: S. Pukalskas, O. Chernashejus, G. Garbincius
Abstract: This research was carried out with an Audi-80 turbo diesel engine that has a supplementary ethanol feed to air intake. The obtained results allowed for a mathematical expression to get a description of the optimal ethanol supply, which ensures the maximum heat efficiency coefficient for different engine working conditions.
109
Authors: Muhammad Arif Abdul Hamid Pahmi, Sharzali Che Mat, Ahmad Nazri Nasruddin, Mohd Fauzi Ismail, Mohd Najib Yusof
Abstract: Intake manifold is a crucial part in an engine that acts as a medium for air flow to mix with the fuel before entering the combustion chamber. For years, cast iron and aluminium were the primary materials chosen for fabrication of an intake manifold before plastic based material was introduced to the field. However, there is lack of research involving the usage of plastic as the intake manifold material. In this paper, the effects of internal surface roughness variations (Cast iron, aluminium and plastic) inside the intake manifold were studied. Three dimensional, intake manifold model was developed to simulate the airflow. The study emphasized on the airflow velocity inside the intake manifold. The study showed that the surface roughness influenced the air flow velocity near the intake manifold outlet. The plastic based intake manifold exhibited the highest air stream velocity (near the intake manifold outlet) at 477.770 m/s. This value is 0.60% and 0.40% higher than those produced by the cast iron and aluminium intake manifold, respectively.
143
Authors: Jiang Feng Mou, Rui Qing Chen, Yi Wei Lu
Abstract: This paper studies the lean burn limit characteristic of the compound injection system of the direct-injection gasoline engine. The low pressure nozzle on the intake manifold can achieve quality homogeneous lean mixture, and the direct injection in the cylinder can realized the dense mixture gas near the spark plug. By adjusting the two injection timing and injection quantity, and a strong intake tumble flow with special shaped combustion chamber, it can produces the reverse tumble to form different hierarchical levels of mixed gas in the cylinder. Experimental results show: the compound combustion system to the original direct-injection engine lean burn limit raise 1.8-2.5 AFR unit.
362
Authors: Tao Liu, Quan Bo Tang, Jian Hua Zhao
Abstract: The oxide inclusion formation tendency in tilting cast magnesium alloys intake manifold was studied by numerical simulation. Two different programs were used for results comparison. The results indicate that it was easier to form oxide inclusion when connecting foundry ladle with the junction panel of intake manifold instead of cavity resonator. The oxidation mixture is prone to appear at the ribs and outer wall of the four main air piles of the intake manifold. The formation of oxide inclusion would be influenced by the flowing state of the melt during casting process.
367
Showing 1 to 8 of 8 Paper Titles