Papers by Keyword: Stress Intensity

Paper TitlePage

Authors: Jun Yan
Abstract: Based on CFD numeric simulation for hydraulic retarder under full-filled condition, the pressure distribution functions of the rotor blades surfaces are approached by coordinate transformation and surface fitting. Through the APDL program, loads which involved not only centrifugal force but also flow pressure are loaded on the FEA model according to the approximating pressure functions. The FEA model is solved and the blades strength is analyzed more accurately. Noted moment and speed, that is respectively 4000 N • m and 1343rpm, is determined under the promise of blade strength, and controlling strategy is made that constant braking torque shoud be carried out when speed is higher than noted value .
1453
Authors: Wei Xu, Xuan Cang Wang, Shan Qiang Li
Abstract: Focusing on the severity of asphalt concrete pavement crack, the optimization analyzing finite element model(FEM) of typical asphalt overlay pavement was developed to address reflective cracking, in which the analysis of traffic-loading response were concentrated on the stress-intensive areas close to the joints or cracks. The FE sensitive analysis, evaluating the influence of pavement construction parameters, including modulus and thickness of pavement courses, is useful to establish comprehensive model of overlay pavement construction.
1623
Authors: You Tang Li, Ping Ma, Chang Feng Yan
Abstract: The anti-fatigued design is an important field in product lifecycle management. A uniform criterion of annularly breached spindle was put forward in this paper. The crack, V-notch, U-notch and arc were described as breach uniformly according to the tip radius, depth and field angle of breach in the method. The connection between sharp V-notch and crack, between V-notch and U-notch has been set up. We fuse the fatigue fracture theory and life prediction techniques together on the design technology of lifecycle safety guarantee of mechanical structures. The relationship between life and detectability of the breached spindle system was discussed to provide useful guidance for practical applications. The criterion for the safety design and fracture design both of which on fα was obtained. The criterion of annular breached spindle under torsion was obtained at first and then the effects of bending to lifecycle of spindle were analyzed.
755
Authors: Vladimir Rodionovich Kargin, Andrey Yurievich Deryabin
Abstract: Computer analysis of distribution of stress intensity and strain intensity in different cross sections of plastic deformation region and in finished material in the course of hot extruding process was carried out. By means of the finite element method in the Deform-2D program influence of small extrusion ratio value on stress-strained state of large 250mm to 500mm dia. bars in 7075 high-strength Aluminium alloy was established.
211
Authors: Nour Eddine El Guemri, Sheng Yuan Yan
Abstract: In a structure the presence of a geometric discontinuity of order or material reduces significantly its lifetime. Indeed, it is at these areas that the stress field is strongly disturbed and can reach very high critical levels resulting a damage process. The analysis of these unique areas can not only achieve an optimal design of the geometry of structures but also can choose materials for various assemblies. This analysis necessarily involves determining the parameters of the asymptotic uniqueness constraints. These parameters are the stress intensity factor, the tensor and standardized the order of singularity. This last parameter that indicates the severity of the singularity. It is directly connected to the geometric aspect, and incompatible materials present in the structure. This study focuses on the identification and analysis of this important parameter in the reliability of structures made of homogeneous materials.
92
Authors: Akira Shimamoto, Hiroshi Ohkawara, Hong Yang Zhao
Abstract: Stress intensity factor K is analyzed by measuring distribution of sum of the principal stresses around slit tip by an infrared stress measuring device. Under the biaxial tensile stress, both K-values of the isotropic materials with slit angle 0° and 45° show there is no influence of the slit angle at Mode I. The tolerance of the measured K-values of the test specimens which are compared with measured K-values by photoelastic method are around 10-20and these increase as applied cyclic load increases. These tolerance can be reduced up to about 8% by modifying measurements. The effectiveness of the thermoelastic stress measurement method to KI value analyzing under biaxial tensile stress was confirmed.
1103
Authors: Jin Li, Guang Sheng Ren
Abstract: According to amonoral parking space in traverse table platform technology parameters requirements and structural characteristics, the use of Pro/e software established structure model and imported into the finite element analysis software analysis Workbench, steel structure of the static analysis. Calculated the steel structures in design load maximum deformation.The results show that, by pro/E a structure model and the calculation method is reasonable, the calculation is of high accuracy, profile choose the proper size, structure deformation meet the design requirements.
1139
Authors: Won Seok Kim, Jung Ju Lee
Abstract: Adhesive bonding between different materials has been widely used for a large variety of applications, such as in the aircraft, automotive, and many other civil engineering structures. Adhesive-bonded joints as load bearing components have the potential to save significant weight and cost over conventional riveted or bolted joints. For the last ten years a major problem in adhesive technology has been the difficulty in predicting the accurate load bearing capacity of a joint. This difficulty comes from the fact that the stress distribution in the adhesive joint is very complex and singular stress field exists at the bi-material corner. And for bonded joints, the failure usually occurs at the adhesive/adherend interface. Therefore another difficulty comes from the complex interfacial failure analysis due to the formation of chemical bonds, whose strengths are difficult to measure. Many studies have been conducted to investigate the effects of bond thickness, material properties of adhesives and adherends, and geometric shape of bi-material corner tip to the fracture behavior of bonded joints. In this paper, we analyze the stress fields at the interface corner of composite/steel(anisotropic/isotropic) double lap joint to predict failure by using stress intensity based fracture criterion. And analytical results are compared with experimental results of co-cured lap joints under tensile load condition. Micro-structural features, hardness characteristics, and fracture toughness determinations of the interfaces are also conducted.
361
Showing 1 to 10 of 20 Paper Titles