Papers by Keyword: Titanium Alloy

Paper TitlePage

Authors: Agnieszka Kochmańska, Paweł Kochmański
Abstract: The slurry aluminide coatings are produced on the three kind of substrates: hightemperature creep resistant cast steel, titanium alloy and nickel alloy. The slurry as active mixture containing aluminium and silicon powders, an activator and an inorganic binder. The coating were obtained by annealed in air atmosphere. The structure of these coatings is two zonal and depend on the type of substrate and technological parameters of producing.
590
Authors: Beata Oleksiak, Leszek Blacha, Lubomir Pikna, Rafał Burdzik
Abstract: In the paper, results of the study on aluminium evaporation from the Ti-Al alloy (6.5%mass) during smelting in a vacuum induction furnace (VIM) are presented as well as the kinetics of the process is discussed. The experiments were performed at 51000 Pa for 1972 K and 2023 K. Based on the determined values of aluminium overall mass transfer coefficient, the mass transfer coefficient in the liquid phase and the evaporation rate constant, the stages that determined the investigated process were defined. It was demonstrated that Al evaporation from the aluminium-titanium alloy is kinetically controlled.
117
Authors: Bin Li, Hong Wang
Abstract: With the development of engineering technology, FEM can be used to simulate metal machining process and gain better understanding of material flow within dies, so as to optimize tooling to eliminate tears, laps and other forging defects. In this paper, numerical simulation was conducted by using FEM software on the whole cutting process for TC4 alloy mounting parts in an effort to investigate the metal flow behavior. The thermal simulation results obtained were compared with the cutting temperature and discussed in terms of literature data.
886
Authors: Gang Liu, Ke Huan Wang, Yi Xu, Bin Wang, Shi Jian Yuan
Abstract: Gas bulging with local-stretching preforming is presented to form titanium alloy tubular part with small radius. In ordinary gas bulging process, local thinning occurs at the corners with small radius and produces dangerous position of the component. In the paper, a preforming process so-called local-stretching is applied before gas bulging. Finite element simulation and experiments were carried out to verify the effectiveness of the preforming and gas bulging process for the tubular component of titanium alloy TA15. During the local-stretching preforming, the material near the corner was kept almost rigid, but the material far away from the corner experienced stretching deformation and thickness thinning. Then, during gas bulging, the material near the corner experienced thinning deformation. So, the thickness uniformity of the final component was improved effectively.
651
Authors: Ming He Chen, J.H. Li, Zhi Shou Zhu
Abstract: This paper develops a three-layer back-propagation artificial neural network model to analyze and predict the correlation between processing parameters and properties of the damage tolerance type titanium alloy TC21. The inputs of the ANN are working temperatures, deformation extent, deformation rate and heat treatment conditions. And the outputs are mechanical properties namely ultimate strength, yield strength, elongation, reduction of area, plane strain fracture toughness and microstructure concerned parameters such as β phase fraction, βphase grain size, substructure length and thickness. The ANN is trained with experimental data and achieves a very good performance, which has already been applied to the optimization of processing for forging of aero-parts.
709
Authors: Shi Jin Zhang, Yu Qiang Wu, Yan Li Wang
Abstract: As abrasive water jet (AWJ) started to be used in industry, especially in aerospace and automotive industries extensively, cutting precision and accuracy has become a major requirement for further application. Unlike a knife which retains a fixed shape as it cuts through material, an AWJ stream is constantly changing. It bounces back-and-forth during cutting process. As a result, a typical surface cut by AWJ displays striation marks on the cutting surface. AWJ’s cutting front can be distinguished as a smooth upper zone and a rough lower zone. As being an energy dissipation beam cutting process, the striation marks couldn’t be eliminated completely on the cutting surface. But, by selecting proper parameters, smoother surface can be generated. However, high quality also means high cost. In manufacturing process, it is desirable to produce qualified parts with the lowest cost. This paper explored all parameters which might affect surface roughness. Based on the experimental results, an empirical model has been built and tested. With this model, predicting surface roughness becomes possible before actual cutting.
4231
Authors: Li Fu Xu, Ze Liang Wang, Shu Tao Huang, Bao Lin Dai
Abstract: In this paper, the cutting experiment was used to study the influence of various cutting parameters on cutting force when rough turning titanium alloy (TC4) with the whole CBN tool. The results indicate that among the cutting speed, feed rate and cutting depth, the influence of the cutting depth is the most significant on cutting force; the next is the feed rate and the cutting speed is at least.
237
Authors: Dyi Cheng Chen, Yi Ju Li, Gow Yi Tzou
Abstract: The shear plastic deformation behavior of a material during equal channel angular (ECA) extrusion is governed primarily by the die geometry, the material properties, and the process conditions. This paper employs the rigid-plastic finite element (FE) to investigate the plastic deformation behavior of Ti-6Al-4V titanium alloy during ECA extrusion processing. Under various ECA extrusion conditions, the FE analysis investigates the damage factor distribution, the effective stress-strain distribution, and the die load at the exit. The relative influences of the internal angle between the two die channels, the friction factors, the titanium alloy temperature and the strain rate of billet are systematically examined. In addition, the Taguchi method is employed to optimize the ECA process parameters. The simulation results confirm the effectiveness of this robust design methodology in optimizing the ECA processing of the current Ti-6Al-4V titanium alloy.
181
Authors: Jian Zhao, Zhan Qiang Liu
Abstract: The purpose of the paper is to investigate the influence of the processing parameters on the surface roughness in rotary ultrasonic burnishing of titanium alloy Ti-6Al-4V plane. A Taguchi orthogonal array for three levels and four factors, which include burnishing depth, feed fate, spindle speed and ultrasonic frequency, are designed. The optimal combination of ultrasonic burnishing process parameters is obtained. Analysis of variance (ANOVA) is applied to determine the most significant processing parameter and to obtain the optimal combination level of processing parameters for the lowest surface roughness. The results show that burnishing depth has the most predominant effect on surface roughness, and spindle speed is the secondary one. Feed rate and ultrasonic frequency are then followed and have no distinct effect on surface roughness in rotary burnishing of Ti-6Al-4V.
406
Authors: A. Galdikas, Jean Paul Rivière, T. Moskalioviene, L. Pichon
Abstract: We have analyzed the interfacial elemental depth profile evolution after high temperature isothermal oxidation of SixCy and SixNy protective coatings deposited by dynamic ion mixing on a Ti6242 alloy (Ti-6Al-2Sn-4Zr-2Mo). Isothermal oxidation tests have been carried out at 600°C during 100 hours in air. We have observed a non-monotonic depth distribution of zirconium in GDOES and SIMS depth profiles after oxidation of SiC/Ti6242 and SiN/Ti6242 and we propose a kinetic model based on rate equations for analyzing the results. It is shown by modeling that a non-monotonic depth profile of zirconium occurs because zirconium from the Ti6242 alloy forms a zirconium oxide compound. As a result, the atomic concentration of zirconium decreases at the interface which induces a diffusion flux of zirconium from the bulk to the interface. This process leads to the increase of the total amount of zirconium at the film interface and thus formation of a non-monotonic depth profile.
433
Showing 21 to 30 of 659 Paper Titles