Paper Titles
Effect of Heat Treatment on the DC Conductivity and Activity Energy of Li2O-Fe2O3-P2O5 Glasses
p.1827
Crystallization of a SiO2-MgO-Al2O3-K2O-Fe2O3-F Glass
p.1829
Making Fluorophlogopite Ceramics through Ceramic Processing
p.1833
Preparation of Decorative Building Glass-Ceramics by Using Cracked-Glass Panel as Precursor
p.1836
Sintering and Crystallization of Glass-Ceramics for Optical Fiber Ferrule
p.1840
Manufacture Process of Light Calcium Carbonate from Limestone
p.1843
Upconversion Emission of Infrared Excited Er3+-Doped Transparent Glass Ceramics Containing CaF2 Nano-Crystals
p.1846
Structuration and Fabrication of Sensors Based on LTCC (Low Temperature Co-Fired Ceramic) Technology
p.1849
Fabrication of Ba-Ti-B-Si-O Glass-Ceramics for LTCC
p.1853

Sintering and Crystallization of Glass-Ceramics for Optical Fiber Ferrule

Article Preview

Abstract:

The crystallization and sintering of the Li2O-Al2O3-SiO2 glass powder compacts were studied. Results showed the relative densities of the sintered compacts with lower crystallization temperatures were higher than those with higher crystallization temperatures. A small amount of residual glass in the crystallized compact was good for sintering and densification. Compared with the heat treatment time, the heat treatment temperature was an important factor for the crystallization and sintering of glass powder compacts. The crystallized compacts with a small amount of residual glass should be sintered at a relatively higher heating rate under the prerequisite of keeping sintered compacts from deformation.

You might also be interested in these eBooks
High-Performance Ceramics IV View Preview

Info:

Periodical:

Key Engineering Materials (Volumes 336-338)

Pages:

1840-1842

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.336-338.1840

Citation:

Cite this paper

Online since:

April 2007

Authors:

Y.M. Zhu, Xia Wan Wu, Zhi Hong Li

Keywords:

Crystallization, Glas Ceramics, Optical Fiber Ferrule, Sintering

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2007 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] E. Sugita, R. Nagase, K. Kanayama and T. Shintaku: J. Lightwave Thchnol. Vol. 7 (1989), p.1689.

Google Scholar

[2] Y. Takeuchi and S. Mitachi: IEEE Photonics Litters. Vol. 9 (1997), p.1502.

Google Scholar

[3] R. Nagase, E. Sugita, S.I. Iwano, et al.: IEEE Trans. Photonics Technol. Lett. Vol. 3 (1991), p.1045.

Google Scholar

[4] K. Kanayama, Y. Ando, S.I. Iwano, et al.: ICICE Trans. Electron. Vol. E77-C (1994), p.1559.

Google Scholar

[5] E. Sugita, R. Nagase and E. K. Sugita: Appl. Optics. Vol. 30 (1991), p.5260.

Google Scholar

[6] T.D. Mathis and C.M. Miller: U.S. Patent: 4850670, July 25, (1989).

Google Scholar

[7] T. Ueda, T. Tanabe, K. Komatsu, et al.: Tech. Rep. IEICE Japan EMD92-99 (1993), p.25.

Google Scholar

[8] A. Sakamoto: New Glass. Vol. 14 (1999), p.26.

Google Scholar

[9] R. Nagase, Y. Takeuchi and S. Mitachi: Electronics Lett. Vol. 33 (1997), p.1243.

Google Scholar

[10] H. X. Lu, L. Luo and G. C. Zhang: J. Inorg. Mater. Vol. 16 (2001), p.237.

Google Scholar

[11] M.C. Wang, N.C. Wu and S. Yang: J. Europ. Ceram Soc. Vol. 23 (2003), p.437.

Google Scholar

[12] M. L. Ernest, R. R. Carl, F. M. Howard: Phase diagrams for ceramists (American Ceramic Society Publications, Columbus, Ohio 1964) p.118. Fig. 5 The SEM photograph of the fracture surface of the sintered compacts treated at 700°C/1h.

Google Scholar