Paper Titles
Fracture Toughness Calculation by Movable Cellular Automata Method
p.774
Temperature Effect on the Friction Behavior of NiTi Shape Memory Alloy
p.780
Gear Abrasion-Induced System Vibration
p.784
Tribological Properties of MoS2-Coated Gray Cast Irons with Some Different Matrix Phases under the Boundary Lubricating Conditions
p.788
Wear Mechanism of Ti(C, N)-Based Cermet Cutting Tools in the Machining of Normalized Medium Carbon Steel AISI1045
p.792
Influence of Laser Micro-Mesh Texturing on the Tribological Performance in an EHL Point Contact
p.796
Reciprocating Triboligical Behavior of PA1010 Filled with ZnOw
p.801
Unequal Interval Grey Forecast of the Rate of High Temperature Abrasion of Water-Wall Tubes in Circulating Fluidized Bed Boilers
p.805
Research on Nano-Mechanical and Micro-Tribological Behaviors of C+- Implanted Silicon
p.809

Wear Mechanism of Ti(C, N)-Based Cermet Cutting Tools in the Machining of Normalized Medium Carbon Steel AISI1045

Article Preview

Abstract:

Ti(C, N)-based cermet cutting tools were prepared by vacuum sintering and tested in dry machining of normalized medium carbon steel (AISI1045) at various combinations of cutting speed (Vc), feed rate (f), and depth of cut (ap). And the wear mechanism was investigated in detail using scanning electron microscopy (SEM) and electron-probe microanalysis (EPMA). Comparing to the cemented carbide YT15 and cermet TN20, the newly fabricated cermet tools exhibited better performance and higher wear resistance. For Ti(C, N)-based cermet tools, the wear mechanism was predominantly controlled by the flank wear under all cutting condition. It was found that the removal of the ceramic grain and abrasive wear were the main source of tools failure. In addition, adhesion and oxidation were also observed.

You might also be interested in these eBooks
Progresses in Fracture and Strength of Materials and Structures View Preview

Info:

Periodical:

Key Engineering Materials (Volumes 353-358)

Pages:

792-795

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.353-358.792

Citation:

Cite this paper

Online since:

September 2007

Authors:

Zeng Min Shi, Yong Zheng, Wen Jun Liu

Keywords:

Abrasive Wear, Cutting Tool, Ti (C,N)-Based Cermet, Wear Mechanism

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2007 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] P. Ettmayer, H. Kolaska, W. Lengauer: Int J. Refr. Met. & Hard Mater. Vol. 13(1995), p.343.

Google Scholar

[2] S. Bolognini, G. Feusier, et al. Int J. Refr. Met. & Hard Mater., Vol. 16(1998), p.257.

Google Scholar

[3] Yong Zheng, Wenjun Liu, et al: Cera. International., Vol. 30(2004), p.2111.

Google Scholar

[4] Jinkwan Jung, Shinhoo Kang: Acta Mate., Vol. 52(2004), p.1379.

Google Scholar

[5] R. Vaßen, D. Stöver: J. Met. Proces. Tech., Vol. 92-93(1999), p.77.

Google Scholar

[6] V. Richter, M. v. Ruthendorf: Int. J. Refr. Met. & Hard Mater., Vol. 17(1999), p.141.

Google Scholar

[7] Guangyong Yang: Jour. Beijing Ins. of Technol., Vol. 14(1994), p.139.

Google Scholar

[8] Zengmin Shi, Yong Zheng, et al: Chinese Jour. Nonferr. Metals., Vol. 16(2006), p.805.

Google Scholar

[9] Modern Indexable Cutters Application Manual. Metallurgy Industry Press, Beijing, (1988).

Google Scholar

[10] S.H. Yeo, S.H. Ong: Jour. Mater. Proces. Technol., Vol. 98(2000), p.317.

Google Scholar

[11] Yudong Xu, Ning Liu, et al: Jour. Chinese Cera. Soc., Vol. 4(2003), p.7.

Google Scholar

[12] Ning Liu, kun Sui, Zhenhua Hu, Sanlou Liu: Tribology., Vol. 19(1999), p.126.

Google Scholar

[13] Qing Zhang: Cemented Carbide., Vol. 12(1995), pp.187-20 u m.

Google Scholar