Papers by Author: Maya Marinova

Abstract: In the present work we report on the polytypic transformations taking place in nanoscale dimensions within 6H-SiC crystals. The examined crystals were grown by Liquid Phase Epitaxy using a mixture of Si and Al as solvents. The study concentrated on the differences from the “correct” stacking order of the Si-C bilayers for 6H-SiC leading to the formation of other polytypes. A great variety of sequences was found, which resulted to the appearance of rare short and long period polytypes or individual lamellae having their “own” stacking inside the 6H-SiC matrix. These nanostructured faults which deteriorate the quality of the grown material indicate also their “sensitivity” to any small or even infinitesimal change of the growth conditions, due to the very small energy among them.

Abstract: The present study reports on the propagation of twin boundaries in (111) 3C-SiC by means of conventional (CTEM) and high resolution transmission electron microscopy (HRTEM). The investigated 3C-SiC layers were homoepitaxially grown by Chemical Vapour Deposition (CVD) on layers previously grown by Vapor Liquid Solid (VLS) mechanism on 6H-SiC substrates. At the initial stages of growth the usual twin boundary that occurs is an incoherent {-211} Σ3 one. It transforms to more energetically favorable cases by several ways: (i) The initial {-211} boundary turns 90º, to a fully coherent (111) interface, forming microtwins; (ii) A step-like interface occurs with facets along the (111) and the {-211} planes; (iii) It transforms in a fourfold twin complex propagating to the surface.

Abstract: Both 3C and 6H stacking faults have been observed in a low doped 4H-SiC epitaxial layer grown in a hot-wall CVD reactor on a heavily doped (off-axis) 4H-SiC substrate. They appear differently on the different parts of sample, with energetic dispersion ranging from 3.01 eV to 2.52 eV. Since they behave as natural type-II quantum wells in the 4H-SiC matrix, the thickness dependence of the excitonic recombination is investigated using the standard effective mass approximation. The results are discussed in terms of built-in electric field and inter-well coupling effects.

Abstract: The current communication focuses on the influence of a post-growth annealing on the evolution of defects inside (111) 3C-SiC layers grown by the Vapour Liquid Solid (VLS) mechanism in SiGe melts on Si-face on- and off axis 6H-SiC substrates. The layers are studied by Transmission Electron Microscopy (TEM) and Low Temperature Photoluminescence (LTPL). It was found that the growth on off-axis substrates results in a 3C-SiC layer containing mainly stacking faults (SFs) and microtwins (MT). The density of MT lamellae and SFs reduces in the layers grown on the on-axis substrate compared to off-axis substrate. In the layers grown on off-axis substrates the annealing strongly reduces the density of SFs inclined to the 3C/6H-SiC interface. Additionally, 3C to 6H polytypic transformation appears only at the interface, most probably starting from substrate step edges. This was only seen on off-axis seed since the step edges are more.

Abstract: The current communication focuses on the investigation of 3C-SiC layers grown by the Vapour-Liquid-Solid mechanism on on-axis Si-face 6H-SiC substrates in SiSn melts with different compositions and at different growth temperatures. The layers are studied by Transmission Electron Microscopy and Low Temperature Photoluminescence. It was found that for melts with Sn concentration higher than 60 at% large Sn-related precipitates are formed. The depth distribution of the Sn precipitates strongly depends not only on the melt composition but also on the growth temperature. Their formation strongly influences the stacking fault density and the dopant incorporation in the layers. Lower Sn concentrations combined with higher growth temperatures should result in 3C-SiC layer with enhanced structural quality.

Abstract: This paper deals with the formation and propagation of twin boundaries (TBs) inside 3C-SiC layers grown heteroepitaxially on -SiC substrate. The equivalent probability of nucleating 60° rotated 3C islands on such substrate lead to the systematic formation of TB upon coalescence of these islands. Elimination of these defects should occur by bending of the propagation direction. Bending through incoherent TBs is usually encountered during both VLS and CVD growth and it generates crystalline defects due to high built-in energy. One would prefer coherent TBs, formed by two-by-two annihilation of neighbouring TBs, which do not form new defect except microtwin inclusion at the interface. Such TB annihilation seems to be a specificity of growth by VLS mechanism. The mechanism of such bending is discussed

Abstract: This work presents the crystalline quality investigation of 3C-SiC unseeded crystals grown from vapor phase. Samples were polished after different crystallographic planes from crystals grown with or without nitrogen flow. The structural and optical investigation showed that the central part of the samples exhibited a very good crystalline quality. The best samples proved to be the {100} growth sectors where the only defects found were stacking faults with a defect density under 103 cm-1. At the edges, i.e. between two adjacent growth sectors, structural investigation by transmission electron microscopy revealed stacking faults and hexagonal polytype inclusions. The nitrogen doping was found not to have an influence on the crystalline quality.

Abstract: The present work deals with the structural properties of silicon carbide in nanoscale dimensions. The examined crystals were 6H-SiC grown by Liquid Phase Epitaxy. The study was concentrated on the stacking faults and any other differences from the “correct” stacking order of the Si-C bilayers for this polytype. Three main types of stacking faults were observed: (i) Cubic lamellae with thickness of four and two Si-C bilayers, always occurring in reverse stacking with respect to each other and separated by at least one unit cell of 6H-SiC; (ii) “twinned” 6H-SiC lamellae separated by a two-bilayer thick cubic inclusion. As a result the sequence in the “twinned” 6H-SiC changes from (3+3-) to (3-3+). (iii) Lamellae showing fringes, the interrelated distance of which suggests inclusion with sequence (22). Further, a high variety of sequences was found, leading to the appearance of rare long period polytypes or individual lamellae having their “own” stacking inside the 6H-SiC matrix. These nanostructured faults which deteriorate the quality of the grown material indicate also their “sensitivity” to any small or even infinitesimal change of the growth conditions, due to the very small energy among them.

Abstract: The dependence of the structure and composition of nanolayered Au/Ti/Al ohmic contacts to p-type 4H-SiC on the initial Ti:Al ratio has been investigated. Two contact compositions, Au/Ti(70%)/Al(30%) and Au/Ti(30%)/Al(70%), have been studied regarding the electrical properties, structure, composition and annealing temperature in the interval 850 – 1000o C. The correlation between the electrical behaviour and structure of the annealed contacts is discussed. Very low resistivity of 1.42x10-5 .cm2 after annealing at 900o C has been obtained for the contact having an initial composition Ti:Al (30:70), while the lowest resistivity of 1.21x10-5 .cm2 has been measured for the contact with a composition Ti:Al (70:30) after annealing at 1000o C. Strong dependence of the contact structure on the Ti:Al ratio and annealing temperature, respectively, has been found out. A presence of two phases, Au2Ti and Al3Ti, in all contacts has been determined after annealing, despite the temperature value and Ti:Al ratio. The TEM analysis reveals that titanium and aluminum silicides and carbides are formed after annealing as the Ti:Al ratio affects the kind of silicides and carbides created. It is obtained that the initial composition of the deposited metal layers influences only the phase composition of the annealed contact but not the grain sizes of the dominant phases formed. The origin of the ohmic properties improvement is explained by the formation of Ti3SiC2 compound and/or enhanced carrier transport by the presence of metal spikes into SiC depending on the initial contact composition and as consequence the optimal annealing temperature.

Abstract: In the present work Conventional and High Resolution Transmission Electron Microscopy has been used to examine the structure and types of interfaces between 3C-SiC and 6H-SiC for samples grown by Sublimation Epitaxy. The layers were grown on on-axis 6H-SiC substrates at different temperature gradients. The changed growth conditions influence on the nucleation of 3C-SiC on the 6H-SiC substrates and their competition with nucleation of 6H-SiC islands. Three specific types of 3C/6H-SiC interfaces were observed and the implications of these observations are discussed.