Paper Titles
Investigation on Material Removal Rate in Rotation Grinding for Large-Scale Silicon Wafer
p.362
A Study on the Mechanical Properties of Ti(C, N) Based Ceramic Tool Material
p.369
Surface Quality Analysis of Milling Hardened Die Steel with Micro-End Mill
p.374
Tool Geometry Effect on Machined Surface Integrity in Precision Turning High-Strength Spring Steel
p.380
Superplastic Bulging of an Al-6Mg-0.3Sc Alloy and Its Forming Limits
p.385
Evaluation on Died-Pressed Binders of Ti(C,N)-Based Cermet Powders
p.390
Study on the Thrust Cutting Force in Ultrasonic Elliptical Vibration Cutting
p.396
Research Status Quo of Simulation Design Methods for Ceramic Tool Materials
p.401
Studies on Exploiting Further the Potential of High Efficiency Grinding
p.405

Superplastic Bulging of an Al-6Mg-0.3Sc Alloy and Its Forming Limits

Article Preview

Abstract:

High strain rate superplastic (HSRS) bulging and cavitation behavior of a cold rolled Al-6Mg-0.3Sc sheet were investigated at the temperature of 798K and at the constant applied flow stress of 6.0MPa. The maximum effective strain of about 2.1 was obtained. The experimental results revealed that the cavity growth was essentially plastic - controlled. HSRS bulging limits of the sheet were further predicted based on the Marchiniak - Kuczynski model and a plastic damage approach. It is able to predict HSRS forming limits of the sheet in a reasonable agreement with the experimental findings even without assuming any initial geometrical defect.

You might also be interested in these eBooks
Advances in Materials Manufacturing Science and Technology View Preview

Info:

Periodical:

Materials Science Forum (Volumes 471-472)

Pages:

385-389

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.471-472.385

Citation:

Cite this paper

Online since:

December 2004

Authors:

G.Q. Tong, K.C. Chan, T.G. Nieh

Keywords:

Bulging, Cavitation, Forming Limit, Superplasticity

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2004 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] R.R. Sawtell and C.L. Jensen: Metall. Trans. Vol. 21A (1990), p.421.

Google Scholar

[2] Y.A. Filatov, V.I. Yelagin and V.V. Zakharov: Mater. Sci. Eng. Vol. 280A (2000), p.97.

Google Scholar

[3] T.G. Nieh, L.M. Hsiung, J. Wadsworth, et al: Acta Mater. Vol. 46 (1998), p.2789.

Google Scholar

[4] N. Blake and M.A. Hopkins: J. Mater. Sci. Vol. 20 (1985), p.2861.

Google Scholar

[5] X.D. Ding, H.M. Zbib and C.H. Hamilton, et al: J. Eng. Mater. Tech. Vol. 119 (1997), p.26.

Google Scholar

[6] M.A. Khaleel, K.I. Johnson, C.H. Hamilton, et al: Int. J. Plasticity Vol. 14 (1998), p.1133.

Google Scholar

[7] Z. Marciniak and K. Kucznski: Int. J. Mech. Sci. Vol. 9 (1967), p.609.

Google Scholar

[8] J.M. Jalinier and J.H. Schmitt: Acta Metall. Vol. 30 (1982), p.1799.

Google Scholar

[9] W.H. Tai: Int. J. Mech. Sci. Vol. 30 (1988), p.119.

Google Scholar

[10] K.C. Chan and G.Q. Tong: Metals and Materials Vol. 4 (1998), p.280.

Google Scholar

[11] G.Q. Tong and K.C. Chan: Scr. Mater. Vol. 37 (1997), p. (1917).

Google Scholar

[12] H. Iwasaki, M. Takeuchi, T. Mori, et al: Scr. Metall. Mater. Vol. 31 (1994), p.255.

Google Scholar

[13] M.J. Stowell: Metal Science Vol. 14 (1980), p.267.

Google Scholar