Papers by Author: C. Basceri

Abstract: Availability of high-quality, large diameter SiC wafers in quantity has bolstered the commercial application of and interest in both SiC- and nitride-based device technologies. Successful development of SiC devices requires low defect densities, which have been achieved only through significant advances in substrate and epitaxial layer quality. Cree has established viable materials technologies to attain these qualities on production wafers and further developments are imminent. Zero micropipe (ZMP) 100 mm 4HN-SiC substrates are commercially available and 1c dislocations densities were reduced to values as low as 175 cm-2. On these low defect substrates we have achieved repeatable production of thick epitaxial layers with defect densities of less than 1 cm-2 and as low as 0.2 cm-2. These accomplishments rely on precise monitoring of both material and manufacturing induced defects. Selective etch techniques and an optical surface analyzer is used to inspect these defects on our wafers. Results were verified by optical microscopy and x-ray topography.

Abstract: Recent advances in PVT c-axis growth process have shown a path for eliminating micropipes in 4HN-SiC, leading to the demonstration of zero micropipe density 100 mm 4HN-SiC wafers. Combined techniques of KOH etching and cross-polarizer inspections were used to confirm the absence of micropipes. Crystal growth studies for 3-inch material with similar processes have demonstrated a 1c screw dislocation median density of 175 cm-2, compared to typical densities of 2x103 to 4x103 cm-2 in current production wafers. These values were obtained through optical scanning analyzer methods and verified by x-ray topography.

Abstract: The development of SiC bulk and epitaxial materials is reviewed with an emphasis on epitaxial growth using high-throughput, multi-wafer, vapor phase epitaxial (VPE) warm-wall planetary reactors. It will be shown how the recent emergence of low-cost high-quality 100-mm diameter epitaxial SiC wafers is enabling the economical production of advanced wide-bandgap Power–Switching devices.

Abstract: Micropipe density (MPD) is a crucial parameter for silicon carbide (SiC) substrates that determines the quality, stability and yield of the semiconductor devices built on these substrates. The importance of MPD is underscored by the fact that all existing specifications for 6H- and 4H-SiC substrates set upper limits for it. Several methods for measuring the MPD are known, however, their reliability and applicability to various types of substrates (e.g. semiinsulating, conducting, etc.) has not been systematically studied. The subject of this paper is a comparative study of various techniques used for the MPD measurement accompanied by statistical analysis of the results. The study was initiated by several organizations working in the immediate field of silicon carbide or in closely related fields and included SiC substrate manufacturers, substrate consumers, equipment manufacturers and universities. The study represented a round robin experiment in which MPD was measured on thirty SiC wafers of various pedigrees. The values of MPD have been determined using both destructive and non-destructive techniques. The repeatability of each technique is analyzed and compared with that of other techniques.

Abstract: The move towards commercialization of SiC based devices places increasing demands on the quality of the substrate material. While the industry has steadily decreased the micropipe (MP) levels in commercial SiC substrates over the past years, the achievement of wafers that are entirely free of MPs marks an important milestone in commercialization of SiC based devices. We present the results of a study for controlling the nucleation and propagation of MP defects in SiC ingots grown via PVT. Our studies confirm that during bulk growth of SiC, foreign polytype nucleation such as 3C-polytype occurs at the initial stages of growth (nucleation period) and/or during subsequent growth in the presence of facets. Results in this investigation suggest that polytype instability during crystal growth adversely impacts the MP density. Based on this key concept, growth conditions for nucleation and growth stages were optimized. These conditions were subsequently implemented in an innovative PVT growth environment to achieve a growth technique with highly effective polytype control. Under continuously modulated growth conditions, MPs induced by seed material and/or formed during the growth were eliminated. 2-inch and 3-inch diameter MP-free (zero MP density) conducting 4H-SiC ingots were obtained.