Search results

These materials have large commercial application due to their physical and chemical properties.
Wang, et al.: Journal of Hazardous Materials Vol. 155 (2008), p. 58
Rashid: Journal of Porous Materials Vol. 17(1) (2010), p. 39
Paul: Microporous and Mesoporous Materials Vol. 82 (1) (2005), p. 1
(Elsevier Science B.V.

These approaches help minimize the number of experimental trials, thereby saving time, materials, and tool wear [4].
Materials and Methods A CNC lathe machine was employed for the machining trials in this study.
Bhambri, “Multi-response optimization by experimental investigation of machining parameters in CNC turning by Taguchi based grey relational analysis”, Materials Science 2 (5) (2012) 1594-1602.
Vekatesh, “Taguchi based grey relational analysis for optimization of machining parameters of CNC turning steel 316 R”, in 2018 IOP Conference Series: Materials Science and Engineering 377 (2018) 012078.
Sharma, “Process parameters optimization using Taguchi’s orthogonal array and grey relational analysis during hard turning of AISI D2 steel in forced air-cooled condition”, in 2019 IOP Conference Series: Materials Science, Engineering 491 (012032) (2019) 1-6.

It well known that almost of the important technologically materials are not available in the nanocrystal way.
Moreover, the powders and pressing materials are easier to be obtained with low cost.
This confirms hypothesis that the microdeformations is caused by release of organic materials in the structure.
Kakihana: Journal of Sol-Gel Science and Technology Vol. 6 (1996), p. 7
A Lessing: Journal of Materials Research Vol. 7 (2) (1992), p.502

Materials and experimental methods Raw materials.
The raw materials used to prepare the clinker of corrosion-resisting cementitious material for fill mining include limestone, gypsum, fly ash, clay, and ferrous powder, all available in producing Portland cement [3].
All the raw materials are dried in an oven at 105℃～110℃ for 4h and ground to pass a 75-mesh sieve.
Zhang: Procedia Earth and Planetary Science Vol. 1(2009), p.736 [2] Y.B.
Chen: Journal of University of Science and Technology Beijing: Mineral Metallurgy Materials Vol. 12(2005), p. 469 [3] B.W.

Recycling product inventory refers to material inventory  used to reprocessing,which comes from the recycled materials after the proprecessing of splitting, cleaning , inspection and testing.
t1 t2 t3 t4 T recovered materials inventory finished products inventory Fig. 2 Variation of recovered materials inventory and finished products inventory Assumptions.In order to facilitate discussion, we make the following assumptions on the system：When the cycle are rather short, the main factors affecting market  demand is relatively stable,  so suppose marketable products market demand rate in different stage is certain.
After a preliminary classification, detection, dismantling, recycling materials are put in recovered products inventory.At the end of the cycle, they will be deal with at a one-time.
Recycling materials can be repaired to be salable and will be put in new products inventory.
References [1] Xiuqin Xia, Daoping Wang: submitted to Journal of Beijing Jiaotong University(Social Sciences Edition) (2011) In Chinese [2] Haolin Tong: submitted to Henan Normal University（2010）In Chinese [3] Nan Wang, Yan Wang, Yan Zhang: submitted to Journal of Shenyang University（2011）In Chinese [4] Qingli DA,Zuqing Huang: submitted to Journal of Southeast university（2005）In Chinese [5] Beilin Liu,Na Chen: submitted to Journal of Harbin University of Commerce（2006）In Chinese [6] Iner Klebera, Stefan Mirinera, Gudrun kiesmullerb: submitted to International journal of Production economics（2002）

Both fixed grout volume method and cement coefficient method are concentrating on the research of cementing materials.
Integrative comparison of mix design method Fixed grout volume method and cement coefficient method are both committed to cementing materials.
This method can improve the class of fine aggregate in concrete and reasonably ensure the fly ash excess coefficient and adjust actual water consumption depending on the specific cementing materials, so that the cementing materials can obtain the optimal amount.
And finally it can save the dosage of cementing materials.
journal of the Chinese Ceramic, 2000（2）：194—198.

The results show that the performance of cement cold regenerated materials meets the requirements.
This is because the old asphalt functions in the cold regenerated materials.
Comparing dry shrinkage coefficient of cement cold regenerated materials with semi-rigid materials, the dry shrinkage coefficient of cement cold regenerated materials is lower than that of the cement stabled macadam, and can satisfy the basic requirements for the subbase materials of high level highway and base of Grade 2nd highway. 3 Conclusions Applicability of basic road performances of cement cold regenerated materials are briefly analyzed through comprehensive performance test results.
Acknowledgments The authors appreciate the support of the Science Foundation Projects of Zhejiang Province (2011H26), and Science Foundation Projects of Shaanxi Educational Department (12JK0795).
Testing and analysis of semi-rigid base pavement in construction period[J].China Journal of Highway and Transport(2001),p.14-08

Experimental Metallic magnesium, aluminum, zinc, manganese and antimony were used as raw materials.
Materials Science and Engineering A, Vol. 302(2001), p. 37 [2] A.A.
Materials Science Forum, Vol. 419-422(2003), p. 57 [3] Q.L.
Journal of Materials Engineering, Vol. 12(2009), p. 80 (in Chinese) [5] S.J.
Journal of Hunan University(Natural Sciences), Vol. 34(2007), p. 47 (in Chinese)

Journal of Manufacturing and Materials Processing, 2(2), 37. https://doi.org/10.3390/jmmp2020037 [5] Ning, J., & Liang, S.
Journal of Manufacturing and Materials Processing, 2(4), 74. https://doi.org/10.3390/jmmp2040074 [6] Ning, J., & Liang, S.
Journal of Manufacturing Science and Engineering, 136(6), 061004. doi: 10.1115/1.4028539 [10] Roberts, I.
Journal of Manufacturing and Materials Processing, 1(1), 3. https://doi.org/10.3390/jmmp1010003 [19] Mirkoohi, E., Ning, J., Bocchini, P., Fergani, O., Chiang, K.
Journal of Manufacturing and Materials Processing, 2(3), 63. https://doi.org/10.3390/jmmp2030063 [20] Ning, J., Sievers, D.

Sustainability represents one of the latest degree subjects that have various trials to connect the social science with the engineering and the environmental science with the future technology.
Vickridge (2004) discussed an approach for social cost quantification for public utility works and included the social costs of traffic, noise, vibration, air pollution, dust, dirt, plant and materials [7].
Canadian Journal of Civil Engineering
International Journal of Traffic and Transportation Engineering.
Canadian Journal of Civil Engineering CSCE (In press).