Search results

The bedrock fissure water wedges into the rock cracks, resulting reduction of rocks cohesion, decrease of internal friction angle, reduction of mechanical strength.
It can store the data.
With a communication cable connected to a computer, you can transfer the data to a computer directly to achieve figures fast and accurately.
In the tunneling site, when there is water-bearing structure ahead of the tunnel face, the abnormal infrared field generated by it will be added to the normal one, and the instrument displays the mutational data of the curve.
The data of field infrared detection are shown in Table 1, Table 2, and curve of infrared detection is shown in Fig.5.

The field data are compared to prediction models.
The testing of paints for prolonging of corrosion protection of weathered galvanized steel structures in real exposure conditions gives important data for long-term durability of large steel structures´ corrosion protection.
The field data are compared to prediction models.
E.g. the planned service life of pole of power distribution network is 50 years and estimated costs to build 1 pole is ca 36 000 € so the prolonging service life for 30 years represents the reduction of cost about 20 000 €.

So the establishment of growth status assessment system for crops can be done by obtaining and analysis hyperspectral image data.
So when the data processed, it used to be select the range 500-800nm.
Therefore, before processing the data, we should resample the hyperspectral image on the ENVI and obtain a three-dimensional data blocks by 1344×800×513.
Principal component analysis (PCA) is widely used for dimensionality reduction, loss data compression, and feature extraction.
This technique projects the data orthogonally onto a lower dimensional linear space so that the variance of the projected data is maximized.

In order to validate the proposed model, we employed experimental data from the HDS setup.
However, it is well-known, ANN and SVM are not capable to model uncertainty and fuzziness of the data.
The powerful of FL lies in its ability to handle uncertainty and to extract rules from the given data.
Table 2 demonstrates the statistical analysis of the experimental data.
The symbol yi represents the experimental value while ӯi refers to the simulated/predicated value of a specific data point i

Energy Dispersion X-ray (EDX) analysis revealed that there was 1.02% reduction of Ru in the Ru/Mn/Ce (5:35:60)/Al2O3 used catalysts compared to fresh catalysts.
Introduction Recently, the increasing demand for natural gas and the reduction of greenhouse gases have became more promising.
The diffractogram was collected over the range of 2θ from 10o to 80o and the data obtained were analyzed by a PC interfaced to the diffractometer using the Diffrac Plus.
EDX analysis reveals that there was 1.02% reduction of Ru in the Ru/Mn/Ce (5:35:60)/Al2O3 of used catalyst compared to fresh catalyst.
The reduction was possibly due to the migration of Ru into porous support during the reaction.

Finite element simulations of the brazing process have been performed to evaluate the expected residual stress reduction near the metal-carbon interface.
In this work another route for the reduction of residual stresses in PFCs has been preliminary explored; it entails the use of high strength and high thermal conductivity, but low CTE or graded CTE interlayers, to be brazed in between the low CTE protective material and the high CTE heat sink.
The easiness of industrialization and the costs reduction of the brazing process could be completely exploited.
Finite Element Modeling Finite Element Modeling (FEM) has been used in order to calculate the expected residual stress reduction near the metal-carbon interface with respect to the pure Cu compliant layer.
Zolti: Materials Data, NET Int.

The observed stress reduction is attributed to the milder ion-induced structural damage by lighter noble gas ions.
Two possible mechanisms are proposed to explain this stress reduction.
Raman spectroscopy showed a correlated decrease in the FWHM of the G peak with stress reduction.
The observed reduction in stress without a change in film density deviates from previously reported trends, and this is considered to be partly due to the higher precursor gas concentration used in this study.
Song et al., “Cross Sections for Electron Collisions with Methane,” Journal of Physical and Chemical Reference Data, vol. 44, no. 2, p. 023101, 2015, doi: 10.1063/1.4918630

Therefore, to determine the coefficients in the quantitative method, real experimental data were obtained and analyzed in MATLAB.
· Effects of optimum configuration and BESS usage on emissions and operational cost reductions were investigated.
Fig. 16 shows the effects of optimum configuration and BESS usage on emissions and operational cost reductions.
Finally, the influence of BESS usage on emission reduction in the microgrid system was also investigated in this study.
Kou et al., "Photovoltaic power forecasting based on artificial neural network and meteorological data," in 2013 IEEE International Conference of IEEE Region 10 (TENCON 2013), 2013: IEEE, pp. 1-4.

ICP-OES analysis data of slurries with abrasive 5%, 3.5% and non-abrasive slurry Table 2.
Fig. 4 shows MRR data of CMP-processed SiC substrates with 5%, 3.5% and non-abrasive content.
AFM image data and roughness of CMP-processed SiC substrates with 5%, 3.5%, and non-abrasive content.
MRR data of CMP-processed SiC substrates with 5%, 3.5% and non-abrasive content.
Scratch mapping analysis data of SiC substrates with 5%, 3.5%, and non-abrasive content after RCA cleaning.

This approach lowers the amount of data, which is sent between the service layer and the transportation entities, by reducing the information of the workspace to the possible routes of each specific vehicle.
CAD data, and the machine-specific sources and sinks can be integrated into the overall layout.
Due to the standardized data exchange between ISP services, the physical design of the platform is irrelevant for the function of the services.
Based on the data of the local path planner, the drive units of the chassis are finally controlled to take the required target position.
Wahl, Camera-based observation of obstacle motions to derive statistical data for mobile robot motion planning, 1998 IEEE International Conference on Robotics and Automation (1998)