Search results

First of all, aggregates were prepared from A, B or mix of both materials.
Material B presents a mechanical performance lower than all of OPC, AL or ALB materials.
Journal of Materials Science 42 (2007), p.2917-2933
Jalali, Construction and Building Materials,Vol. 22, (2008), p. 1201-1211 [10] J.
Construction and Building Materials, Vol. 22, (2008), p. 1315-1322

The selected materials were a 0.20-mm thick, obtained by cold (secondary)-rolled and continuous annealing or cover annealing, coated with an electrolytical substrate.
Journal of Materials Processing Technology, 152(2004), p.384-388
Journal of Iron and Steel Research, 13-4 (2001), p. 38-41.
Corrosion Science, 52(2010), p.14-20
Materials Protection. 33 -3 (2000), p.1~3.

But these fibrous materials, along with high strength characteristics, are characterized by surface inertness and low adhesion to matrix polymers, which limits their use for reinforcing composite materials.
Abldullin, Modification of synthetic fibrous materials and products by nonequilibrium low-temperature plasma.
Kashapov, High-frequency plasma-jet processing of materials at reduced pressures.
Zheltukhin, Modification of synthetic fibrous materials and products by nonequilibrium low-temperature plasma.
Karnoukhov et al, Influence of plasma modification on free surface energy of synthetic fibrous materials, Journal of Physics: Conference Series. 1588 (2020) 012052

Muhammad Safwan1e, M.K Anis Sofiah1f, 1School of Materials Engineering, Universiti Malaysia Perlis, Kompleks Pusat Pengajian Jejawi 2, 02600 Arau, Perlis, Malaysia. 2School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang, Malaysia.
Introduction In recent years thermoplastic materials have been increasingly used for various applications [1].
The TG curves indicate the thermal stability of the materials, whereas the DTG curves shows the decomposition temperature of the materials.
Mater Science Engineering, 11(1), 1-7
Journal of Emerging Trends in Engineering and Applied Sciences, 2, 346-350

Bottom ash is a waste byproduct generated from the combustion or incineration of materials such as coal and household waste.
Bottom ashes generated from the incineration of municipal solid waste (MSW) are a mix of inert materials, such as sand, stone, glass, porcelain, metals and ashes from the burnt materials.
The high Al2O3 content on many bottom ashes can result in low cost materials that are corrosion and abrasion resistant.
We would also like to thank the Department of Materials Science, Faculty of Science, Srinakharinwirot University, and Department of Physics and Materials Science, Faculty of Science, Chiang Mai University for providing access to their research facilities.
-H., 2008, “Recycling MSWI bottom and fly ash as raw materials for Portland cement”, Waste Management, vol. 28, pp. 1113–1118

Introduction Metals, like most of construction materials, have creep properties under certain values of stresses and temperatures.
Murashkin, On the residual stresses in the vicinity of a cylindrical discontinuity in a viscoelastoplastic material, Journal of Applied Mechanics and Technical Physics. 47(2006) 241-248
Levitas, Large deformation of materials with complex rheological properties at normal and high Pressure, New York, Nova Science Publishers. 1996
Bruhns, A thermodynamically consistent Eulerian description of finite elastoplasticity, Key Engineering Materials. 340-341(2007) 787-794
[9] Yao Ying Huang, Hong Zheng, Yi Hong Zhou, Simulation analysis of concrete Dam’s joints based on elastic-plastic creep model, Applied Mechanics and Materials. 137(2011) 243-249 [10] Wen Ling Chen, Fa Suo Zhao, Study on non-linear viscous elastic-plastic creep model of mica-quartzose schist, Applied Mechanics and Materials. 157-158(2012) 622-627.

Materials Mg, Al, and Zn were used as raw materials to prepare the AZ91 alloy in the experiment.
Materials Science and Engineering, Vol.
Journal of Materials Processing Technology, Vol. 117 (2001), p.276
Materials Science Forum, Vol. 488 (2005), p.393
Materials Science and Engineering, Vol.

NAKA2, c 1 School of Materials Science and Engineering, Harbin Institute of Technology, P.O.
Ductility of these materials can be improved by several methods.
Koch: Materials Science and Engineering Vol.
Zhang: Journal of Materials Processing Technology, Vol. 48 (1995), p. 683 [6] B.
Zhang: Progress in Materials Science Vol. 49 (2004), p. 537 [8] G.

The yield strength and the ultimate strength of the 3 materials are listed below.
Table 1 Yield strength and ultimate strength of the 3 materials in this case study.
Miner, Journal of applied mechanics 12 (1945) A159-A164
Tomita, Materials science and technology 7 (1991) 481-489
Phan, International Journal of Fatigue 29 (2007) 2060-2071

Introduction The releasing of elastic energy which produced by the micro cracks initiation, development, and ultimate fracture of rock-like materials, causes the rock-like materials have acoustic emission (AE) phenomenon.
On this basis the cataclysms of rock-like materials also can be forecasted [1,2].
As one of man-made materials, cemented backfill contains a large number of micro holes and micro cracks in its internal.
Lockner: International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts, Vol. 30 (1993) No.7, p.893
Meredith: International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts, Vol. 30 (1993) No.1, p.11