Search results

Number of challenging problems still exist in "classical" areas of nucleation, reactive and interdiffusion, phase growth in multicomponent and binary systems, decomposition and ripening.
The problems on diffusion and reactions, structural and phase transformations, surface and grain boundary diffusion, driven systems, fundamental problems of diffusion, special diffusion problems were considered.

A large number of crack type line indications were detected by magnetic particle inspections, while the occurrence of partial penetration in roots of welded joints was detected by ultrasonic inspections, as well as lamellar tearing of the base material.
A large number of micro- and macro-cracks were detected in the microstructure as well.
Magnetic particle inspection showed a large number of surface crack type line indications on all welded joints of 4 segments.
Grain size has been determined by microscopic examination of polished cross-section of the sample, employing the method of comparison with standard cards for grain size measurement and in accordance with standard EN ISO 643/2012 [14].
[14] EN ISO 643, Micrographic determination of the apparent grain size, European Committee for Standardization, 2012

Ten lines were arranged parallel to the center line at intervals of 3 mm, numbered A1-A5 lines for those above and B1-B5 lines for those below respectively.
Because the center line had a maximum width of the air-gap of the slot, it also had the maximum number of opposite magnetic charges accumulated on the two cracked surfaces of the slot.
Similar to the mode of static failure, the grains on the unstable crack propagation zone of the fracture were torn at the instant of failure.
Hence, a large number of magnetic charges generated and gathered on the unstable crack propagation zone and the strong abnormal magnetic signals were emitted.
During the stage of unstable crack propagation, the crystal grains on the final fracture zone were torn.

Once finishing the specified number, sensor node automatically entered sleep mode.
(2) When AT+TCPCONNECT=”IP address” was sent, TCP server connection of a fixed IP was tried to establish by number>
The extractive bunch of grapes had 50 grapes whose total weight was 535g, so single grain weight was 10.7g.
It is initially known, the number of grapes on bunch was more, and the grapes were bigger.
When grape grains were big, the color was also very smooth, but maturity wasn’t uniform.

Referring to Eq. 1, Nf is the number of cycles performed during the last loading block before failure occurred.
The image analysis showed that the amount of primary α grains was estimated equal to about 50% and the average grain size was about 30 µm.
Navy (Contract Number: N00014-08-1-1197).

By planting melilotus offcinalia, soil physical structure has been effectively improved with loose soil, increasing water holding capacity and soil aggregates number.
The number of soil porosity has increased by 14.29% for two years.
According to the degree of the difficulty of soil improvement and the demand for land use, the mode of rotation or intercrop of forages and grains is selected to improve ecological environmental and promote the sustainable use of land resources.
Melilotus offcinalia can enhance land fertility, improve the yield of grains and forages and ease the food contradiction between human and livestock, which is of great strategic significance for the security of land resources and food of China.

But because of its crystal structure with a close six-party, it is difficult to effect plastic deformation at room temperature, what's more, under high temperature it is prone to coarse grains and surface oxidation [3-4], the current products of magnesium alloy including castings, especially die casting, and few plastic processing products.
In order to improve the efficiency of calculation, analysis in the process of selecting 1/2 as the research object, the meshing forgings and specify the grid cell number is 80000, divided into the three dimensional model is shown in Fig.2 after the unit parameter setting of mould material AISI-H13 steel, the mould is set to the rigid body; Blank temperature and mould temperature were 400 ; The friction coefficient is 0.2; Dynamic model movement rate of 3 mm/s.
Fig. 3 (d) for the fourth stage, in this process, the billet is completely full of cavity, excess metal be reemployed in the storage bin, a small number of flying edge of punch and die clearance, contact with the punch, load increases further, the metal in the mould of three to the compressive stress state, create conditions for the metal fills the cavity, when the rounded corners is filling.
If higher temperature, can predict the site may occur the phenomenon of coarse grains, therefore in the process of experiment, magnesium alloy 6061 control arm in the constant temperature of 400 , the forging rate of 3 mm/s is the best.

Introduction Iron ore reserves have a large number in the world, total reserves of iron ore is over 780 billion tons, of which about 2/3 are magnetite[1].
The first is stage grinding and separating for coarse-grained ore, the representative ore dressing plants are Nanfen, Waitoushan, Panzhihua and Dashihe [3].
Therefore, large number of the monomer dissociation magnetite particles into the second stage of the grinding and classification cycle.
In this case, it is not only increases the burden of grinding, consume more energy, but also over grinding, and lead to the loss of micro-fine-grained magnetite.

Introduction Since no single crystal nickel-based alloy grain a boundary during high temperature service to eliminate the weakening of grain boundaries, and has a high volume fraction of the g¢ phase and good high temperature performance, has been widely used to prepare the aircraft engine blade parts [1].
Such representations are particularly useful for complex functions with continuous-valued outputs and large numbers of noisy inputs, where the logic-based techniques in chapter 18 sometimes have difficulty.
A neural network is composed of a number of nodes, or units, connected by links.

It provides the estimated value of the average crystallite size calculated peaks per lines, final weighted average Bragg R-factor (%), value of the final reduced chi2 and number of peaks matched out of total number of peaks in range.
For a figure exhibiting semicircles, it is understood that the material is semiconducting with interfacial boundary layers (grain-boundary).
The charge carriers are settled on the portion of grain boundaries with sufficient energy to overcome the barrier with increase in temperature and hence we can emphasize conductivity.