Search results

Ramin Hosseinzadeh [13] analyzed the use of glass mat thermoplastic and high-strength sheet molding compounds for front bumper beams.
International Journal of Vehicle Design 21 (4-5): 424–35 [5] Duan, L., Sun, G., Cui, J. et al.
H. (2019) “Crashworthiness Evaluation of Side-Door Beam of Vehicle”, Technische Mechanik - European Journal of Engineering Mechanics, 28(3-4), pp. 268–278
International Journal of Crashworthiness
Antoun (1999) Development and validation of high fidelity vehicle crash simulation models, International Journal of Crashworthiness [28] Fang, H, Solanki, K, & Horstemeyer, MF.

In this paper, some preliminary results are presented, included in a vast research project with the aim of a better understanding of the different factors influencing the hardness of hard W-Si-N films.
Three materials with different thermal expansion coefficients were used as substrate: refractory steel 310 (AISI) - �s=17.0x10 -6K -1, Fecralloy � (Goodfellow) - �s=11.1x10 -6K -1 and TZM (Mo alloy - Goodfellow) - �s=5.3x10 -6K -1.
The �-W phase is most probably the W3Si compound, as previewed by Goldschmidt [10], since no significant oxygen content (<1at.%) was detected in the films.
Anand; International Journal of Plasticity, 1 (1985) 213
Golschmidt in “Interstitial Alloys”, ed.

Micro-silica is a very fine pozzolanic material, composed of amorphous silica, obtained as a byproduct of the silicon or ferro silicon alloys (Fe5Si2) industry, that can be used in a variety of cementitious based products, such as concrete and mortars.
The usual proportions of compounds varies in the following limits: SiO2 – 20...60%, Al2O3 – 5...35%, Fe2O3 – 10...40%, CaO – 1...12%.
Portland cement) in the presence of water produces cementitious compounds.
Rodríguez, Silica nano-particles produced by worms through a bio-digestion process of rice husk, Journal of Non-Crystalline Solids 355 (2009), 844–850
Tsai, Effects of nano-SiO2 and different ash particle sizes on sludge ash–cement mortar, Journal of Environmental Management 88 (2008), 708–714

Owing to this, the aim of this study is to observe the optimal preheating temperature on the growth tendency of c-axis orientation of ZnO thin films fabricated on indium tin oxide (ITO) coated glass substrate by sol-gel spin coating technique.
Saim , Journal of Nanoscience and Nanotechnology 10 (10) (2010) 6419
Chami, F.Yakuphanoglu, Journal of Alloys and Compound 490(2010)62-67.

The aim of experimental design using the Taguchi approach is to select system design parameters that reduce the variation of the system’s performance around the target value, i.e. to obtain near optimum design values while conducting only a limited number of experiments.
Journal of Thermal Spray Technology 2005; 14; 405-413. 3.
Journal of Quality Technology, 12, 214–219. 5.
Journal of Alloys and Compounds 2009;467; 163–167. 10.

Thus, this work aims to investigate the zinc doping in titanium dioxide powder samples by the well-known sol-gel method.
Fujishima: Journal of Photochemistry and Photobiology C: Photochemistry Reviews Vol 13 (2012), p. 169
Zhang: Chemical Engineering Journal Vol. 236 (2014), p. 388
Alloys Compounds Vol. 466 (2008), p. 435
Cortie: Chemical Engineering Journal Vols. 185–186 (2012), p. 1

The fish fillet usually contains water, salt and other compounds.
As the water in the fish progressively freezes, the concentration of salts and other compounds in the remaining water would increase.
The Fluent software can model the solidification of pure liquid as well as binary alloy solution.
Journal of Food Technology Vol. 21 (1986), p. 209-219
International Journal of Heat and Mass Transfer Vol. 48 (2005), p. 1205-1213.

This approach efficiently explores the temperature dependent thermal boundary condition for a group of friction stir welds of 7449 aluminium alloy.
The aim of the ANN is to find the values of the CSRR, and contact gap conductance parameters, a and b.
Proceedings of 4th International Friction Stir Welding Symposium, 2003(Journal Article)
Colegrove, and J. dos Santos, Hybrid modelling of 7449-T7 aluminium alloy friction stir welded joints.
Suxing Gongcheng Xuebao/Journal of Plasticity Engineering, 2008. 15: p. 284-197.

This study aims to contribute a deeper understanding on the utilization of RPB in the geopolymer products such as blocks /bricks and thus, reducing the amount of Portland cement used for environmental friendly purpose.
Journal of Cleaner Production.
KSCE Journal of Civil Engineering.
Journal of Alloys and Compounds.

The present study therefore, is aimed at examining the effects of magnesium on the dielectric constant of CaTiO3.
Moderate to high Mg doping however has been reported to contribute to grain refinement which has been attributed to the dopants or compounds formed that diffuse to the grain boundary area and act as pinning agents that thus inhibit grain boundary mobility.
Jafarian, Synthesis of perovskite CaTiO3 nanopowders with different morphologies by mechanical alloying without heat treatment.
International Journal of Physical Sciences.
Journal of the European Ceramic Society 27. (2007), 1077-1082