Search results

A Vicon motion capture system was used to collect the kinematic data of lower limb and Kistler force platform simultaneously recorded the ground reaction force (GRF) during vertical jump.
Fig. 1 Passive static stretching of knee flexors muscles Data Collection and Statistical Analysis.
The flight time, which is used as a measurement of vertical jump height, was calculated using data of the force plate.
The Paired-Samples T test was taken to determine significant differences between key biomechanical data, including flight time, ground reactive force (GRF), and the peak joint (hip, knee, ankle) angle at each specific phase of vertical jump.
The flight time, which is used as a measurement of vertical jump height, was calculated using data of the force plate.

The pressure drop predictions compare favorably with literature data and the coefficient of variation (COV) value for circle grid perforated plate with 50% porosity at Reynolds number 100 was 0.0744 which is out of the range meanwhile at Reynolds number 200 and 400 was 0.0483 and 0.0247 respectively which are in the range of reasonable target for many applications.
On the other hand, this radial reduction of hole diameter assists in stabilizing the velocity distribution.
In this case, the COV will defined as the standard deviation of concentration over the mean of concentration for given set of N data points.
The standard deviation of the concentration can be shown in equations as below: (1) (2) To obtain the data to calculate the COV, a specified number of grid nodes at a cross section identical plane were taken.

According to the roadmap, a 30% reduction in the global cement consumption in the next 20 years is achievable by more efficient use of concrete in structures and better methods of concrete mix-proportioning.
Additionally, a 50% reduction in clinker consumption is achievable from a substantial use of complementary cementing materials that are available worldwide.
References [1] http://www.ccement.com/news/Content/42071.html [2] http://www.sxdaily.com.cn/data/bsswhh/20051226_8829216_0.htm [3] http://www.chinaccm.com/30/3012/301201/news/20060720/084143.asp [4] P.

These issues, plus the lack of statistical data, make designers to have their own methods and algorithms (e.g. [2], [3] and [4]).
Initial estimation of the aerodynamic lift and drag coefficients by statistical data is removed in this process.
So the weight estimation using statistical data of the other similar aircrafts is removed.
So, a wing loading analysis may be needed in the base of statistical data. 5 - Engine nacelle and pylon.
Giguere, “Summary of Low-Speed Airfoil Data, Volume 1”, Soar-Tech Publications, 1995, pp. 202-205

The activity coefficient in Eq. (1b) is typically calculated using the assessed activity data of the liquid phase based on the WLE formalism [14].
In this work, however, it is calculated from the liquid phase substitutional solution data of the IAD database [15], which provides thermodynamic data for iron based alloys with solutes Al, C, Cr, H, Mn, N, Nb, Ni, O, P, S, Si, Ti and V.
Both terms are calculated with the substitutional solution model and data.
For the current data provided by Ruukki in Finland, only hydrogen content in continuous casting (CC) mould is measured.
The calculated results show agreement with the measured data in CC mould to some extent if the hydrogen pick-up varies between 0.7 and 0.9 ppm.

As shown in Figure 1, the data collected by each sensor node is transmitted to the only data sink node through ZigBee network.
The hardware logic includes data acquisition, data transmission and power management.
To reduce the amount of network transmission, acquired data is firstly pre-treated or compressed, then uploaded to the data aggregation node.
So data aggregation node is always in the receiving state.
Table 1 General structure of KVP and MSG frame 4 bits 4 bits data data data The bytes of data Frame type transmission data 1 ....... transmission data N Sensor node program can send data after the cluster definition and data aggregation nodes binding with the use of zdpBindReq () function.

Hydroforming process is used for obtaining different kinds of sheet metal components in an economic manner in terms of time and costs reduction and increase of the product quality.
Based on the experimental data a numerical model was designed.
The data of the profiles has been generated on a notepad file, and then exported to excel.

The luminous efficacy and color rendering index (CRI) reduce with power reduction because of the decrease of spectral continuum.
Thus 27 groups of effective data were obtained with a step of 10 W when lamp power ranged from 100 W to 250 W.
It can be predicted that the lamp voltage will continually drop with further increased power according to the two groups data obtained at 250 W.

Alkaline-activated concrete production can therefore lead to a significant reduction in environmental impact.
The first figure shows the structure of waste generated by types in 2017 according to data from the Central Statistical Office.
Structure of waste generated by types in 2017 according to data from the Central Statistical Office [3].

The communication data are successfully transmitted using a low-cost ZigBee wireless network.
Data Communication.
Sensor nodes exchange data in different ways, which are controlled under the software.
The calibration data are sent to every smart PV module from the base station, where the internal parameters of the control system are calculated based on practical data.
All data are passed using the most reliable communication links and most cost-effective path.