Search results

Electroless Sn Deposition on Magnesium Alloy and Wastewater Treatment Liyuan Niu 1, a, Yichang Su 2,b ,Daren Sun 1,c ,Li Guangyu 2,d 1 Advanced Material R&D Center, Zhejiang Industry & Trade Polytechnic, Wenzhou 325003, China 2 College of Materials Science and Engineering, Jilin University, Changchun, 130025, China a ccnly@sina.com, b charisclear@sina.com, c sundaren@sina.com, d guangyu@jlu.edu.cn Keywords: Electroless Sn, Deposition, Magnesium alloy, Wastewater treatment Abstract: The new process electroless Sn deposition on cast AZ61 was revealed, which employed to AZ61 magnesium alloy automobile parts and could provide high wear-resistant and high hardness.
Anticorrosion conversion coating content lanthanum and phosphate on foam Mg alloy Advanced Materials Research 2011, 299-300: pp 211-214 [4] H Umehara, M Takaya, S Terauchi.
Forum, 2003, 419(4): 879-883

Jeon 4,f 1 School of Advanced Materials Engineering and Research Center for Advanced Materials Development, Chonbuk National University, Chonju, Chonbuk, 561-756, KOREA 2 Partsnic Limited, Chongup, Chonbuk, 580-100, KOREA 3 LS Cable Limited, Chongup, Chonbuk, 580-810, KOREA 4 Dept. of Dental Technology, Gwangyang Health College, Gwangyang, 545-703, KOREA a gyu1224@nate.com, bkwseol@chonbuk.ac.kr(corresponding author), cilsong@chonbuk.ac.kr, d glorystar@hanmir.com, e knwoo@lscable.com, fjeonwy@kwangyang.ac.kr Keywords: Electrodeposition, Titanium substrate, anodizing, Arabic gum, Chlorine, HEC Abstract.
Forum Vol. 426-432 (2003), p. 3715 [4] H.W.

Picas4,d 1,2,3,4 Department of Materials Science and Metallurgical Engineering.
A progressive decrease of the same defects is observed as it is advanced in the optimization of the process.
Advanced Materials and technologies for transportation industry.
Forum.

Saddow 1 1 Dept. of Electrical Engineering, USF, 4202 E.
Introduction The growth of 3C-SiC on Si substrates offers the prospect of a low cost, high performance semiconductor film for advanced electronic and mechanical devices and sensors.
This paper reports on a high-quality CVD process to grow heteroepitaxially 3C-SiC on (111)Si substrates for possible use in advanced electronic device and MEMS applications.
Reyes et al.: Materials Science Forum Vols. 556-557 (2007), p. 191 [9] J.

IFITA '10 Proceedings of the 2010 International Forum on Information Technology and Applications, Publisher IEEE Computer Society Washington, DC, USA , kunming,china.pp. 354-357, 2010
Advanced Research on Computer Science and Information Engineering, Communications in Computer and Information Science Vol.153 (2011), pp. 87-92
,Multi-and Megavariate data analysis,Part Ⅱ,Method Extensions and Advanced Applications,Chapter 23,Umetrics Academy,2005

Aircraft Mounted Neural Network Electrostatic Discharge (ESD) Location Paul Ratnamahilan Polycarp Hoole1, Nur Farah Aziz2, Velappa Ganapathy2, Jeevan Ganeshan2, Harikrishnan Ramiah 2, and Samuel Ratnajeevan Herbert Hoole3,a 1School of Engineering, Taylor’s University, West Malaysia 2Department of Electrical Engineering, University of Malaya, West Malaysia 3 Office of the Coordinator for engineering, University of Jaffna, Jaffna, Sri Lanka a.
Introduction Despite the rapid advances in the design and development of a variety of safety and security systems, aircraft safety systems which are mission critical systems, have not advanced at the same rate as, for instance, safety systems for land based motor vehicles.
Rakovic: Materials Science Forum Vol. 214 (1996) pp. 139-146 [2] M.A.
Meng: Materials Science Forum Vol. 686 (2011) pp. 792-796 [8] D.I.

The ICMSE2021 is becoming one of the leading international conferences for presenting novel and fundamental advances in material science and engineering in China.
Sajid Hameed, petroleum processes engineering college, tikrit university, Iraq Dr.
Shafiul Ferdous, Khulna University of Engineering & Technology, Bangladesh Dr.
Parthiban Kathirvel, School of Civil Engineering, India Dr.
Hojjat Toiserkani, Graduate University of Advanced Technology, Iran Dr.

Optimal Design on Reduction Device based on the most Small Gear-Worm Jie Yu1,a, Pei-si Zhong2,b 1 College of mechanical engineering, Shandong University of Technology ,Zibo255000,China; 2 College of mechanical and electronic, Shandong University of Science and Technology, Qingdao 266000,China ayujiezb7@sdut.edu.cn, bpeisizhong@163.com Keywords: Reduction device of gear; Optimal design Abstract.
Forum Vol. 83-87 (1992), p. 119 [2] M.A.
Mishing, in: Diffusion Processes in Advanced Technological Materials, edtied by D.

Modeling of Adsorption Isotherms for Supercritical Hydrogen on A and X Zeolite Xiao-Ming Du * School of Materials Science and Engineering, Shenyang Ligong University, Shenyang 110159, China du511@163.com * Corresponding author.
Forum Vol. 663-665 (2011), p. 934 [3] S.
Advanced Materials Research, 2011 (in press) [6] L.

Fig. 3 shows the obtained temperatures at the varying of the tool advancing speed.
As it can be observed the weld obtained with a tool advancing speed of 400 mm/min is characterized a perfect bonding, with the material coming from the thick blank on the retreating side and being shifted to the thin sheet on the advancing side.
Mishra, Z.Y Ma, Friction stir welding and processing, Materials Science and Engineering R: Reports 50 (2005) 1-78
Fratini, A continuum based FEM model for friction stir welding - model development”, Materials Science and Engineering: A 419/1-2 (2006) 381-388
Simoncini, Friction stir welding of magnesium alloys under different process parameters, Mater Sci Forum 638–642 (2010) 3954–3959.